Download  Print this page

GE SuperBus 2000 Installation Instructions

Rs-232 automation module
Hide thumbs
   

Advertisement

Quick Links

Product Summary
®
The SuperBus
2000 RS-232 Automation Module allows you to
connect compatible, third-party automation devices to Concord
(v2.5-later), Concord 4, Concord Express (v4) and Advent
panels.
For added security, you can install a magnet and reed switch (not
included) for tamper protection.
The RS-232 automation module includes the following features:
• Automation ports
• Supervised, fire-rated zone inputs
• On-board status indicators
• SuperBus 2000 addressing data bus
Figure 1.
RS-232 Automation Module Components
Circuit Card
Bus Status
LED
Module
Power LED
Table 1.
Module Component Descriptions
Components
Power LED
Indicates module power status.
Bus LED
Indicates panel bus communication.
RS-232 Status LED
Indicates module transmit/receive.
Device ID Number
Identifies device ID numbers.
RS-232 Connector
Connects Panel to automation devices.
PHAST Connectors
N/A
Wiring Terminals
Provides power, bus, and hardware zone inputs.

Installation Guidelines

• When powering bus devices and hardwired sensors from the
panel, do not exceed the panel's total power output. Refer to
specific panel Installation Instructions for further detail.
• The module's maximum current draw is 35mA.
• Use four-conductor, 22-gauge or larger stranded wire to
connect the module to the panel.
• Mount the module within 25 feet of the automation device.
Tools and Supplies Needed
• Slotted and Phillips screwdrivers
• 3/8"-drive drill and drill bits
• Wire cutter/stripper
• Four-conductor, 22-gauge or larger stranded wire
• Nine-pin RS-232 serial cable
• 1/4" press-fit reed switch and magnet (not included)
SuperBus

Installation Instructions

SuperBus 2000
ID Label
RS-232 Serial
Connector
I D : X X X X X X X X
PHAST
RS-232 LED
Connectors (2)
Wiring Terminals
Function
®
2000 RS-232 Automation Module
Installation
To prevent damage to the panel or module,
CAUTION
remove the panel's AC power transformer and
disconnect the backup battery before installation.
the Module on a Wall
Mounting
1.
Loosen cover screws and remove module cover and circuit
card (see Figure 2).
Figure 2.
Removing Cover and Circuit Card
Cover
Circuit Card
Backplate
2.
Place the backplate on the wall and mark the mounting
holes (see Figure 3).
Figure 3.
Wall Mount Hole Locations
Mounting Holes(4)
Wire Channels(3)
Enclosure
Backplate
3.
Drill for the mounting holes and insert wall anchors. Next,
secrue the backplate to the wall with the included screws.
4.
Install the circuit card on the backplate and gently press the
bottom of the board until it snaps into place under the card
latches (see Figure 2).
466-1876 Rev. B
June 2005
Card Latches (2)
Cover Screws (2)
Wire Access
Card Latches (2)

Advertisement

loading

  Summary of Contents for GE SuperBus 2000

  • Page 1: Installation Instructions

    Loosen cover screws and remove module cover and circuit • Automation ports card (see Figure 2). • Supervised, fire-rated zone inputs • On-board status indicators • SuperBus 2000 addressing data bus Figure 2. Removing Cover and Circuit Card Cover Figure 1.
  • Page 2 SuperBus® 2000 RS-232 Automation Module Installation Instructions Wiring Wiring Devices to a Module Connect a DB-9 serial cable to a module connector (see Wiring the Module to an Advent Panel (v1.6-later) Figure 5). The serial cable must not exceed 25 feet in length. Remove panel AC power and disconnect the backup battery.
  • Page 3: Troubleshooting

    FCC Part 15 Information to the User B U S B Terminals G N D Changes or modifications not expressly approved by GE Security can void the user’s authority to operate the equipment. Wiring Harness Z O N E 1...