Orbit 94075 Installation And User Manual

4-Button Digital Hose Faucet Timer
Installation and user's guide
INTRODUCTION
Thank you for selecting a quality Orbit ® timer. You will enjoy
many years of satisfactory service if proper installation and
care is observed.
The Orbit timer keeps your yard beautiful whether you are at
home or away. Orbit gives you convenience and flexibility, let-
ting you use an automatic watering program or override the
automatic program for special watering needs.
The Orbit Timer provides up to 3 start times per day with water-
ing periods from 1 to 99 minutes per start time. For ease of use,
the User's Guide has step-by-step instructions for installation,
set up and operation. Please read the guide
completely before installing, programming and operating.
Note: Use only with three 1.5 –volt (AA) alkaline batteries.
SET AUTO MANUAL OFF DELAY
Mo Tu We Th Fr Sa Su
88 : 88
CYCLE
ABC
CLOCK
+ –
MODE NEXT CONFIRM
FIGURE 1
KEY PAD AND DISPLAY
Indicates different mode settings for Indicates the time to begin watering.
programming.
Indicates clock, start time and watering
Select to set day of the week, to set duration.
clock time, to set watering day(s), to set
Push to select or unselect a setting.
watering station and duration and to set
Push to confirm a new setting and
start times.
advance to the next setting.
Select to use automatic watering mode.
Push to increase numeric setting or
Select to enable watering manually.
advance a setting.
Select to suspend watering and turn off
Push to decrease numeric setting or
all stations.
retract a setting.
Select to postpone watering for up to 24
Push to cycle through the different
hours.
mode settings.
Indicates the number of hours remain-
Indicates low battery, or that batteries
ing on the Delay.
need to be replaced.
Indicates current day of the week and
Indicates that the setting of the clock
the set days for watering.
and day of the week is in process.
Indicates which days are selected for
Indicates which watering cycle is active
watering.
or being set.
Indicates the duration that each station
One pinhole "Reset" button: Push to reset
will water. all programs and settings.
Indicates A.M. or P.M. for clock and
start time.
INSTALLATION
GENERAL INFORMATION
Models: 94075, 62075
1. Location:
Choose a spot where water drains away from house and
window wells.
Warning: For outdoor use in cold water only.
2. Plumbing Codes:
Follow all watering and back-flow (anti-siphon)
prevention codes.
3. Specifications:
Water pressure: Min. 10 psi/Max. 80 psi working pressure
Working Temperature: Min. 32 degrees F/Max. 167º F
Storage Temperature: Min. -22 degrees F/Max. 185º F
Electrical: Three AA 1.5-volt alkaline batteries
4. Installing the Batteries:
Remove timer cover and slide battery compartment cover off
in the direction of arrow.
Install three AA 1.5-volt alkaline batteries. Slide compart-
ment cover back into place.
Check the timer periodically for low voltage. When the
battery power drops below the safety zone, the "Low
Battery" indicator appears on the display. Replace the bat-
teries with new fully-charged batteries when this appears.
If old batteries are not replaced before they run out, all
controls will be disabled.
5. Replace the timer cover.
PROGRAMMING
SET CLOCK TIME AND DAY OF WEEK
Push the indented RESET area to erase the current settings.
Push MODE button to select SET. The word SET will blink
to indicate that it is selected.
Push CONFIRM button to begin the set mode. The word
CLOCK will appear to indicate the time/day setting is active.
Push
The day selected will flash.
2nd 3rd
SET
Mo Tu
MINS
AM
TO
CLOCK
RUN
PM
START
MODE
FIGURE 2
Push CONFIRM button to accept the day setting and
advance to set the clock time. The current time with
A.M. or P.M. will flash.
Push + or – button to select the correct current time.
Push CONFIRM button to accept the time setting and
advance to set watering days.
SET
Mo Tu
CLOCK
MODE
FIGURE 3
Push MODE button to return to Mode Selecting.
NOTE: When no button has been pressed for 1 minute, AUTO mode will
automatically switch on to the programmed settings.
or button to select the current day of the week.
We Th Fr Sa Su
CONFIRM
We
7:30
AM
+ –
CONFIRM
SET WATERING DAYS
Your Orbit timer allows you to choose the days of the week for
watering. You can water every day, only certain days or every
2nd or 3rd day.
Push MODE button to select SET. The word SET will blink to
indicate that it is selected.
Push CONFIRM button to begin the set mode.
Push CONFIRM button two more times to move past the
time/day setting. The days of the week will be flashing.
SET
Mo Tu We Th Fr Sa Su 2nd 3rd
NEXT
FIGURE 4
Push or button to advance to the next day, or to the
2nd and 3rd day settings.
When chosen day(s) are flashing, push the () key to toggle
the rain drop (insert raindrop) on/off. The rain drop indicates
the day(s) chosen for watering.
When the watering days are chosen, push NEXT button to
advance to set watering duration.
SET
Mo Tu We Th Fr Sa Su 2nd 3rd
NEXT
FIGURE 5
NOTE: If you choose to only water at intervals of every 2nd or 3rd day,
you cannot set specific days of the week for watering. When no button
has been pressed for 1 minute, AUTO mode will automatically switch on
to the programmed settings.
SET DURATION AND START TIME FOR WATERING
The Orbit timer allows you set the duration and start time for
watering in each of three watering cycles.
Push MODE button to select SET. The word SET will blink to
indicate that it is selected.
Push CONFIRM button to begin the set mode.
Push CONFIRM button two more times and NEXT button
once to move past the time/day setting and the watering
days. MINS TO RUN will show with two digits or "- -" flashing.
SET
--
MINS
TO
RUN
+ –
MODE CONFIRM
FIGURE 6
Push + or – button to set the duration desired for watering,
from 1 to 99 minutes.
Push CONFIRM button to confirm the duration and advance
to set start time.
There are three unique start times, or cycles, that can be
set: CYCLE A, CYCLE B and CYCLE C. Each cycle will appear
on the screen to specify which one is to be set.
SET AUTO MANUAL OFF DELAY
-- : --
CYCLE
ABC
START
+ –
MODE CONFIRM
FIGURE 7
Push + or – button to set the start time for CYCLE A.
Push CONFIRM button to accept this time and advance to
set CYCLE B.