Orbit 96894 Quick Start Manual

timer

quick start

guide
. .
. . .
.
.
.
. .
.
.
. . .
. . . . . . . .
. . .
.
. . .
. .
. . .
. . . .
. . . . .
. . . . .
PROGRAM
RAIN DELAY
RESET
AUTO
required tools:
Phillips Screwdriver
Wire Strippers
PN 96894-50 rA
proof no:
date: 05.19.10
des: SM
job no:
client:
sku: 96894
p 801 295 9820
upc:
NA
f 801 951 5815
www.fluid-studio.net
file name:
1065 South 500 West
software:
Bountiful, Utah 84010
1. Select location
Indoor
.
.
. .
.
.
.
. . .
.
.
.
.
.
. .
.
.
. .
. .
. . .
. . .
.
Clean, dry, and out of direct sunlight
Allow 23 cm clearance for the swing door
Or
Outdoor
.
For detailed instructions on outdoor wiring, see manual page 8
Warning: Check state and local codes. Orbit recommends using a
licensed electrical contractor for outdoor wiring of timer.
1
dimensions:
flat: w: 16" h: 14"
finished: w 16" d: " h 14"
spck: XX
colors
NA
fold color color
Registration non printing non printing
Orbit
PMS
PMS
K ???? ????
additional instructions:
· Font sizes cannot be smaller than 7 pt.
96894-50 rA.indd
· Accordian Fold
InDesign CS3
2. mount timer
MOUNTING TEMPLATE
4.17"
GABARIT D`INSTALLATION
(106mm)
GUIA DE COLGAR
AUTO
3 dimensions:
proof no:
fl at: w: 9" h: 7"
Use included mounting template to date: 10.05.07 fi nished: w 9"
des: SM spck: SM
colors
job no: 07WTM005259
mark screw locations.
Registration
client: Orbit
sku: 57880 K
p 801 295 9820
upc:
f 801 951 5815 ? ????? ????? ? additional instructions:
www.fl uid-studio.net fi le name: 07WTM005259 ·
·
1065 South 500 West 57880-04 rA.indd
Bountiful, Utah 84010 software: Illustrator CS2
Keyhole
Pre-formed
mounting holes
Hang timer on screw using keyhole.
Screw through one of the
pre-formed mounting holes.
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
PMS
???? © 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
3. connect Sprinkler
valveS to timer wireS
Wire Nut
Solenoid
Printers are responsible for
meeting print production
d: 0" h 7" requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
crop color color
non printing non printing designated specifi cations
on this form.
PMS PMS PMS
???? ???? ???? © 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Connect one of the two wires from each valve to the
common wire leading to the timer (usually white).
Connect the other wire from each valve to one of the
colored wires leading to the timer.
3 mm
4. connect valve wire
No. 8 Screw
to terminal
Do not connect to power
source until after wiring
Wall
valves to timer
Only connect one valve to
each terminal (station)
Station 1
Strip wire
Push in
Level
Common Wire
To
Timer
Valve
Push tab
upward to
release wire