Related Manuals for HOME8 WTS3100
Summary of Contents for HOME8 WTS3100
- Page 1 Wi-Fi 3-IN-1 Trio Sensor (WTS3100) User Manual home8alarm.com Wi-Fi 3-IN-1 Trio Sensor User Manual V1 2018 1-844-800-6482 | support@home8alarm.com...
-
Page 2: Table Of Contents
Table of Contents Chapter 1. Introduction ................. 2 System Requirements ....................3 Chapter 2. Hardware Overview ..............4 Chapter 3. Device Setup ................5 3.1 Power On the Device ....................5 3.2 Adding the Device to the System ................5 3.3 Testing and Installing the Device ................ -
Page 3: Chapter 1. Introduction
Equipping the Trio Sensor with the IP-camera can assist the owner and authorized video users to monitor and verify through real-time video for utmost peace of mind. The service can be easily added into the Home8 system in minutes. -
Page 4: System Requirements
1.1 System Requirements This section explains the system requirements when using the device. Router with Network - 10/100Mbps RJ45 LAN port - DHCP service Apple iPhone, iPad, or Android device with: - iOS 8.0 or later Mobile Device - Android 4.0.3 and up * See Appendix –... -
Page 5: Chapter 2. Hardware Overview
Chapter 2. Hardware Overview This section provides an overview of the Device. Sensor Magnet Wi-Fi 3-IN-1 Trio Sensor User Manual V1 2018... -
Page 6: Chapter 3. Device Setup
Chapter 3. Device Setup 3.1 Power On the Device Pull and remove the black plastic strip in the back of the device to initiate battery contact. The LED will flash red for a second. 3.2 Adding the Device to the System Before you begin using the device, it will need to be added to the system first. - Page 7 2. Tap “Device Management”. If you have more than one Security Shuttle/Hub, you may need to swipe left more than once to find the one you wish the sensor to connect to. After selecting the Security Shuttle/Hub, tap the plus icon “+” located to the right of “Sensor”. 3.
- Page 8 4. Follow the on-screen instructions to scan the QR code located on the device, the “sensor adding” process will begin. If your device isn’t communicating with the Security Shuttle, your app may ask you to reset your device. Go to Chapter 4. section 4.5 Reset for instruction. 5.
-
Page 9: Testing And Installing The Device
3.3 Testing and Installing the Device After the “sensor adding” process has been completed, to make sure the connection of the device is working, take your device to the room you want to use it in. Test the device by pressing the tamper switch for 5 seconds and then release it. -
Page 10: Chapter 4. Starting To Use The Device
Chapter 4. Starting to Use the Device At this stage, your sensor is now ready for use. 4.1 Edit Sensor Go to “Device management”, and select the sensor you want to edit. Rename Sensor Tap “Display Name” to rename the sensor. Remove Sensor To remove the sensor from the current Security Shuttle, tap “Remove Sensor”. -
Page 11: Notification
Contact & Motion Setting Here you can enable/disable the function of contact and motion sensor by turning on/off the button next to the feature. 4.3 Notification When the door/window state has changed, motion has been detected or temperature has reached the threshold, a notification will be sent to all authorized users. -
Page 12: Activity Log
4.4 Activity Log You can check the contact & motion activity log from the app. Go to the "Activity" tile and select the sensor. Contact Different colors are used to show the status of the door/window. Detailed information can be seen in "See All Data". -
Page 13: Reset
Motion Shows the result of motion detected with 15-minute intervals in a scatter chart. Detailed information can be seen in "See All Data". 4.5 Reset If your device isn’t communicating with the Security Shuttle, your app may ask you to reset your device. •... -
Page 14: Appendix - Glossary Of Terms
Appendix – Glossary of Terms Arm: The cameras and other security related sensors in the system are actively monitoring the surroundings. Any suspicious activity that has been detected by the camera or sensor will prompt the app to immediately send a notification.