Daikin website (publicly accessible). 4.2.4 To prevent the outdoor unit from falling over ....Connecting the water piping............▪ The full set of latest technical data is available on the Daikin 4.3.1 To connect the water piping........extranet (authentication required).
Use the following graph to determine the maximum water volume for diffusion tight according to DIN 4726. The diffusion of the calculated pre-pressure. oxygen into the piping can lead to excessive corrosion. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
More technical specifications of the different connections test (check that the user interface does NOT display error are indicated on the inside of the outdoor unit. 7H). Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Prepare 6 sets of anchor bolts, nuts and washers (field supply) as When providing drainage, therefore make sure to cover the entire follows: unit. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
2 Place the 2 cables over the outdoor unit. 3 Insert a rubber sheet between the cables and the outdoor unit to prevent the cables from scratching the paint (field supply). Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
▪ Protection against freezing: the glycol will prevent the up inside the hose. liquid inside the piping from freezing. Lowest expected Prevent from Prevent from outdoor bursting freezing temperature –5°C –10°C –15°C –20°C — –25°C — EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
7 Repeat steps 5 and 6 until no more air is purged and there are no more pressure drops. ▪ Remote outdoor sensor (option) 8 Close the drain and fill valve. 9 Disconnect the water supply hose from the drain and fill valve. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
When installing field supply or option cables, foresee sufficient cable length. This will make it possible to remove/ reposition the switch box and gain access to other components during service. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
2 Connect the cable of the domestic hot water pump to the bottom side of control box terminals X8M/8+9. 1× 1× Notch this part for the wiring to pass through with nippers etc. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
> Information > User permission level. ▪ "To access the installer settings" on page 13 3 Press for more than 4 seconds. ▪ "5.3 Menu structure: Overview installer settings" on page 20 Result: is displayed on the home pages. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
(languages, schedules etc.) will be synchronised from the selected source user interface to the other one. Installer settings The system will restart. Cancel Confirm Adjust Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
4 After configuration, select Confirm layout and press Confirm layout Please confirm the system layout. The system will restart and will be ready for first startup. Cancel Confirm Adjust EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
▪ 4 (3PN,(1/2)): 6 kW 3N~ 400 V (*9W) ▪ 2: N/A ▪ 5 (3PN,(1/1+2)): 9 kW 3N~ 400 V If there are two zones (main (*9W) +additional), then only Thermo ON/OFF is possible. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
2, but between the scheduled heatup and more economic operation. cycles, reheat operation is allowed. ▪ 2 (Scheduled only): The domestic hot water tank can ONLY be heated according to a schedule. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
[6‑0D]=0 ([A.4.1] Domestic hot water Type=Reheat only) in case of a domestic hot water tank without an internal booster heater. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Forced pump OFF Emergency [A.7] Commissioning Test run UFH screed dryout Air purge Actuator test run INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
The shut-off valves are properly installed and fully open. fluid is NOT collected, it might drip on internal components and damage the unit. The pressure relief valve purges water when opened. EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Possible actuator test runs make sure the following is clear for the user: ▪ Fill in the installer setting table (in the operation manual) with the ▪ Booster heater test actual settings. Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Technical data A subset of the latest technical data is available on the regional Daikin website (publicly accessible). The full set of latest technical data is available on the Daikin extranet (authentication required).
Page 25
Overcurrent fuse booster heater Main PCB F2U (A4P) Fuse T 2 A 250 V for 3-way valve Current loop PCB Relay for heating EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Page 26
F1T, F2T Thermal fuse backup heater S5P-S6P # Electrical meters Fuse T 5 A 500 V backup heater X*A (A4P) Connector option Terminal strip Contactor backup heater (step 1) Optional Field supply Installation manual EBLQ+EDLQ011~016CAV3+W1 Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...
Page 27
3 core Control box power supply: 230 V + earth X1M: L-N-PE X1M: L-N-PE 2 core 230 V External indoor thermistor X2M: 1a-2a Power supply signal Only for KRCS01-1 4D115044-1 EBLQ+EDLQ011~016CAV3+W1 Installation manual Daikin Altherma low temperature monobloc 4P522031-1 – 2018.01...