JVC VN-H57U Series Instructions page 2

Step 3 Connection of the camera to the PC
1 Launch Internet Explorer.
1
Enter the IP address of the camera (for example, the factory default of "http://192.168.0.2").
2
Click [ ].
2 Enter the user name and password (to log in as the administrator).
Memo
•
If the [Security Information] window appears, click [Yes] to proceed.
Step 4 IP address setting for the camera
1 Click [Details] of the Built-in Viewer.
2 The [Basic Setting1] screen appears.
1
2
1
Specify the [IP Setting].
■
When selecting "DHCP Disable":
Select "DHCP Disable" for the [IP Setting] option. Then, enter required values in [IP Address], [Subnet
Mask], and [Default Gateway].
■
When selecting "DHCP Enable":
The "DHCP Disable" (the DHCP client function is off) is set as factory default. To assign an IP address
from the DHCP server, connect the camera to the LAN where the DHCP server exists. Set the [IP
Setting] of the camera to "DHCP Enable" and click [OK].
Note
•
Set the DHCP server so that the same IP address is always assigned to the MAC address of the
camera, using the DHCP server. The connection may fail if the above settings are not made.
2
Select the [Time Zone].
Set up the IP address if required.
3
Click [OK].
Memo
•
For detailed network settings, consult your network administrator.
•
If you enter the following URL in the address bar of Internet Explorer, you can log in with administrator
privileges proceeding 2 in step 3 and you can directly access the [Basic Setting1] page without going
through the Built-in Viewer.
Example: http://192.168.0.2/cgi-bin/display.cgi?basicmenu1.html
•
If a [Security Warning] window appears, click [Yes] to proceed.
1
2
1
Enters a user name. (The factory default is "admin")
2
Enters a password. (The factory default is "jvc")
3
Click [OK].
1
2
3
Click
3
3 The Built-in Viewer of the camera is displayed.
■
If the IP address of the camera is not known
You cannot set up or change the IP address of the camera from the PC even if the IP address of the
camera is not known.
You can identify the IP address in the following ways.
• Access the "TOOL_E" folder of the supplied CD-ROM disk, and search for the camera in the LAN
using the "JVC-VN-SearchTool" of this folder.
* For the "JVC-VN-SearchTool" details, please open the "README" fi le in the [TOOL_E] folder.
3 When the confi rmation window opens, click [OK].
• The camera restarts with the new IP address. The camera takes about 90 seconds to restart.
Memo
•
As the IP address of the camera is changed, you may not be able to access the camera from the
PC you have been using. If you access the camera from the same PC, set the IP address of the PC
accordingly.
■
If the display or confi guration of the open window appears strange, check the PC
settings as follows:
1
Select [Start] - [Control Panel] - [Appearance and Personalization]
2 Select [Display] - [Adjust screen resolution]
3 Check that [Resolution] is set to [Monitor size (recommended)].
4 Otherwise, change the setting to [Monitor size (recommended)] and
press the [OK] button.
5 In [Display Settings], press the [Keep changes] button.
Advanced camera settings and operation
In addition to the above basic settings, you can set the advanced camera functions using Internet Explorer
and Built-in Viewer as follows.
Camera setting using Internet Explorer
Confi gure the picture quality and alarm settings using Internet Explorer.
* For details, refer to the "Instructions (Setting)" of the supplied CD-ROM disk.
Operating the Built-in Viewer
* For details about the Built-in Viewer, refer to "Built-in Viewer Operations" section in the "Instructions (Setting)"
of the supplied CD-ROM disk.
© 2012 JVC KENWOOD Corporation LST1270-001B
2