Table of Contents

Advertisement

: DOOR ENTRY UNIT
Programming Software
M OD E LS: EI S-1, EI S-2 OR EIS- 4
USER MANUAL
v.02 2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EIS-2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Transmitter Solutions EIS-2

  • Page 1 : DOOR ENTRY UNIT Programming Software M OD E LS: EI S-1, EI S-2 OR EIS- 4 USER MANUAL v.02 2018...
  • Page 2: Table Of Contents

    EIS-1, EIS-2, EIS-4 USER MANUAL Contents FOR YOUR SAFETY .............................. 4 INTRODUCTION ..............................5 EIS-1, EIS-2, EIS-4 FEATURES AND APPLICATIONS ................... 6 START UP ................................7 LED INDICATION ..............................8 CONNECTION DIAGRAM ........................... 9 EIS UNIT MANAGEMENT ..........................10 EIS FUNCTIONS WITH PROGRAMMING INSTRUCTIONS..............11 WEB SERVER - LOG IN ..............................
  • Page 3 EIS-1, EIS-2, EIS-4 USER MANUAL Figures Figure 1: EIS: Connection diagram .....................9 Figure 2: WEB Server-Sign In page ....................11 Figure 3: WEB Server-Main page select ADD mode................12 Figure 4: WEB Server-Main page adding EIS units................13 Figure 5: WEB Server-Unit management window ................14 Figure 6: WEB Server-Intercom settings...................15 Figure 7: WEB Server-Keypad PIN Access: Permanent PIN codes ..........17...
  • Page 4 EIS-1, EIS-2, EIS-4 USER MANUAL Tables Table 1: WEB Server-SPIN entry parameters...................18 Table 2: WEB Server-SPIN entry parameters........Error! Bookmark not defined. Table 3: WEB Server-Timer setting, output mode options ...............26 Table 4: Wiegand 26: Mode 0......................35 Table 5: Wiegand 26: Mode 1......................35 Table 6: Wiegand 26: Mode 2......................35...
  • Page 5: For Your Safety

    EIS-1, EIS-2, EIS-4 USER MANUAL FOR YOUR SAFETY SWITCH ON SAFELY Do not switch the unit on when use of wireless phone is prohibited or when it may cause interference or danger. INTERFERENCE All wireless phones and units may be susceptible to interference, which could affect performance.
  • Page 6: Introduction

    USER MANUAL INTRODUCTION EIS-1, EIS-2, EIS-4 (EIS) is a simple but powerful GSM intercom communication system designed to ensure low-cost, simple to install/use, reliable and single box solution for intercom application. It is designed for unlimited range, wire free GSM intercom, pin code access, caller ID control and Wiegand access support.
  • Page 7: Eis-1, Eis-2, Eis-4 Features And Applications

    EIS-1, EIS-2, EIS-4 USER MANUAL EIS-1, EIS-2, EIS-4 FEATURES and APPLICATIONS Features: ⇒ Built-in 5 band GSM module ⇒ Up-to 4 intercom call button support (5 numbers each) ⇒ Keypad Access entry support (up-to 1000 PIN codes) ⇒ Caller ID numbers control (up-to 1000 caller ID numbers) ⇒...
  • Page 8: Start Up

    EIS-1, EIS-2, EIS-4 USER MANUAL START UP EIS unit accepts a standard GSM Sim (T-Mobile or AT&T) card. VERY USE A MICRO SIM CARD IMPORTANT WARNING DO NOT Insert or remove the SIM card while the unit is powered ON!! Before inserting SIM card to unit make sure the PIN code is...
  • Page 9: Led Indication

    EIS-1, EIS-2, EIS-4 USER MANUAL LED INDICATION Blue LED (LED1) Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak signal, 5 is excellent signal) Red LED (LED2) GSM module Activity Yellow LED (LED3) Short flashing indicates that the GSM module is ON, but it is not yet connected on the GSM network.
  • Page 10: Connection Diagram

    EIS-1, EIS-2, EIS-4 USER MANUAL CONNECTION DIAGRAM Before connection the EIS please take a look at connection diagram. Figure 1: EIS: Connection diagram ******************************************************************************** ******************************************************************************** DO NOT USE Power out (12V AUX) for electric lock driving! Use IMPORTANT separate power source for door electric lock!
  • Page 11: Eis Unit Management

    EIS-1, EIS-2, EIS-4 USER MANUAL EIS UNIT MANAGEMENT Unit supports different types of management (programming): ******************************************************************************** Unit can be programmed remotely by using WEB server access. ⇒ Access it by EISWARE.com EISWARE APP on IPHONE or ANDROID ⇒ Must have data plan enabled to get data transfer on either method.
  • Page 12: Eis Functions With Programming Instructions

    EIS-1, EIS-2, EIS-4 USER MANUAL EIS FUNCTIONs with PROGRAMMING INSTRUCTIONs As mentioned in previous chapters EIS unit can be programmed in various way, this document will focus on most common programming way: WEB programming. SIM card in the EIS unit MUST have DATA PLAN to be able to use WEB...
  • Page 13: Web Server - Adding Units To User Profile

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.2 WEB SERVER – ADDING UNITS TO USER PROFILE After login the user will be diverted to WEB server main window. This page is used to add/remove/search for EIS units from the user’s profile. Select “+” sign to select ADD EIS units to user’s profile.
  • Page 14: Figure 4: Web Server-Main Page Adding Eis Units

    EIS-1, EIS-2, EIS-4 USER MANUAL Figure 4: WEB Server-Main page adding EIS units User than provides required data: • Name: Name for the added unit - mandatory information. • IMEI: Identification number of the unit, can be found in the enclosure of the unit - mandatory information.
  • Page 15: Web Server-Unit Management

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.3 WEB SERVER-UNIT MANAGEMENT After the EIS unit is added to user database, the user can change the configuration of the specific unit. All changes made by the user are listed in the Change Log window. By clicking Send to device button ALL changes are send to the unit.
  • Page 16: Intercom Configuration

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.4 INTERCOM CONFIGURATION Primary function of the EIS unit is intercom support. Selecting (calling) apartment number is achieved pressing the call button beside appropriate name plate. This actions will start a voice call procedure from Phone number 1 till Phone number 5. After the call is answered the called user has the option to trigger the output by pressing “11”...
  • Page 17 (buzzer BEEP) when the apartment entry is selected, by selected Muted unit will provide no audio feedback when the apartment entry is selected. EIS-1 has 1 CALL button. NOTE EIS-2 has 2 CALL buttons. EIS-4 has 4 CALL buttons. Page 16...
  • Page 18: Keypad Pin Entry - Access

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.5 KEYPAD PIN ENTRY – ACCESS Secondary use of on-board keypad is access by entering PIN codes. Pin codes must be at least 4 digits. Pin codes can be defined in two sections. First section is permanent pin code and second is temporary pin codes which are limited by the consecutive time they are entered.
  • Page 19: Figure 8: Web Server-Adding Wiegand Devices With Temporary Use

    EIS-1, EIS-2, EIS-4 USER MANUAL Figure 8: WEB Server-Adding Wiegand devices with temporary use. • Temp PIN codes activate output: Selecting the output that will be triggered in case of correct SPIN code. • SPIN entry: For each SPIN entry user need to select appropriate values.
  • Page 20: Wiegand Access

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.6 WIEGAND ACCESS EIS unit has onboard support for 2 Wiegand output based device. With the use of external replicator more Wiegand devices can be connected to the unit. Configuration of first Wiegand interface is found in Digital interface tab.
  • Page 21: Figure 10: Web Server-Wiegand Interface Support

    EIS-1, EIS-2, EIS-4 USER MANUAL Additional settings for Wiegand interface input are found in Wiegand input 2 configuration section. Figure 10: WEB Server-Wiegand interface support. • Mode: Select appropriate data formatting (Advise unit provider for more info if needed, mode 2 is most common setting) •...
  • Page 22: Caller Id Access

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.7 CALLER ID ACCESS Caller ID access is a very simple way to control relay output defined in Caller ID output setting. User will by calling in the EIS unit trigger defined output. Settings for this function are found in the Caller id # tab.
  • Page 23: Outputs Settings

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.8 OUTPUTS SETTINGS The behavior on the outputs is defined in the Output tab. Figure 12: WEB Server-Output setting Output 1 - Settings for output 1: • Output (relay) mode: User can select between 3 options Disable-Output is disabled.
  • Page 24 EIS-1, EIS-2, EIS-4 USER MANUAL Output 2 - Settings for output 2: • Output (relay) mode: User can select between 3 options Disable-Output is disabled Latching-Output is in latching mode. First Caller ID or PIN entry will activate the output, second Caller ID or PIN entry will deactivate the output.
  • Page 25: Eis Wiegand Output Integration

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.9 EIS WIEGAND OUTPUT INTEGRATION EIS unit can be integrated into a bigger access system using a Wiegand interface. In this case number’s calling the EIS unit will be transferred, over Wiegand interface, to access system. Figure 13: WEB Server-Wiegand Output settings.
  • Page 26: Timer-Timed Controled Output

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.10 TIMER-TIMED CONTROLED OUTPUT EIS unit features 2 timers that can be used to control the outputs on the unit. Timers can run in day or week mode depending on the selected setting. For each timer user can select which output it will control.
  • Page 27 EIS-1, EIS-2, EIS-4 USER MANUAL Timer settings: • Timer: Parameter is used to enable and disable the timer function. • Mode: User can select between day or week mode. In day mode the timer will control on the day table which is the same for all week. In week mode the user can define different setting for each day in the week.
  • Page 28: Administration

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.11 ADMINISTRATION Administration tab allows user to enable advanced settings: notification of unauthorized access, periodic test messages, lock down of the unit… Figure 16: WEB Server-Notification numbers • Phone number, User name: Phone number and user name of the user that will be receiving notification messages.
  • Page 29 EIS-1, EIS-2, EIS-4 USER MANUAL • Low credit alert: In case of prepaid SIM card the unit can notify the user if the credit on the SIM card is low. To enable notification SMS tick the check box in corresponding position. Note that additional input in the Misc. tab is needed to fully enable credit checking function.
  • Page 30: Event Loging

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.12 EVENT LOGING EIS unit itself support a 20000 log events entry. These log events can be pull up to the server by clicking Read Log button in the “Event Log” tab. Events are listed in the table.
  • Page 31: Miscellaneous

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.13 MISCELLANEOUS This tab is split into 2 sections. Figure 19: WEB Server-Misc. General settings can be found: • SMS text Language: define the language of the SMS information send out. User can select appropriate language in drop-down menu.
  • Page 32: Pin Access Notification Function

    EIS-1, EIS-2, EIS-4 USER MANUAL 8.14 PIN ACCESS NOTIFICATION FUNCTION This function is used to notify administrator when a selected pin code is being used. Notification is done by SMS send to the selected administrator numbers. Global enabling of the notification function is done in 2. Steps.
  • Page 33: Figure 23: Web Server-Selecting Administrator Numbers For Notification

    EIS-1, EIS-2, EIS-4 USER MANUAL The last step is selecting a number that will be receiving the notification SMS. Selecting is done in the Administration tab. In the Notify PIN column put a tick in the check box for the appropriate phone number, multiple choices are possible.
  • Page 34: Wiegand Input Data Formats

    EIS-1, EIS-2, EIS-4 USER MANUAL WIEGAND INPUT DATA FORMATs EIS units support standard Wiegand interface, it will work with Wiegand 26bit and Wiegand 30bit protocol. On each Wiegand protocol EIS unit support 4 different data formats, they all can be selected through all possible management systems.
  • Page 35: Figure 25: Web Server-Second Wiegand Interface Support

    EIS-1, EIS-2, EIS-4 USER MANUAL Figure 23: WEB Server-Second Wiegand interface support. Page 34...
  • Page 36: Wiegand 26 Bit, Different Data Formats

    EIS-1, EIS-2, EIS-4 USER MANUAL 9.1 WIEGAND 26 BIT, DIFFERENT DATA FORMATS Possible data format: Mode 0: All 24bit of data are used a decimal representation, no option for facility code Parity Parity 24Bit card number Limits Card Number 0 - 16777215 Facility Number None Table 3: Wiegand 26: Mode 0.
  • Page 37: Wiegand 30 Bit, Different Data Formats

    EIS-1, EIS-2, EIS-4 USER MANUAL 9.2 WIEGAND 30 BIT, DIFFERENT DATA FORMATS Possible data format: Mode 0: All 30bit of data are used a decimal representation, no option for facility code Parity 28Bit card number Parity Limits Card Number 0 - 268435455 Facility Number None Table 7: Wiegand 30: Mode 0.
  • Page 38 EIS-1, EIS-2, EIS-4 USER MANUAL Page 37...

This manual is also suitable for:

Eis-4Eis-1

Table of Contents