Advertisement
Quick Links
•
ijt
FI
BAR
G R
O U
P
OPERATING MANUAL
FIBARO ROLLER SHUTTER 2
FGR-222-EN-A-v1 .00
FIBARO Roller Shutter 2 is a universal, 2-Wave compatible, electric
motor controller. The device allows for controlling motors of roller
blinds, awnings, venetlan blinds, gates and others, which are single
phase AC
powered.
FIBARO Roller Shutter 2 allows for precise
posltioning of a roller blind or venetian blind slats. Precise
positioning is available for the motors equipped with mechanic and
electronic end switches.
The module may be controlled wirelessly, through the Z-Wave
network main controller, or through the switch keys connected to
it.
Jt's also possible to combine few devices into groups of devices,
which then can be controlled simultaneously. In addition
,
FIBARO
Roller Shutter 2 is equipped with Power Metering.
1. SPECIFICATIONS
Power
supply:
Power consumption
:
Operational temperature:
Dimensions (L
x
W
x
H):
For installation in boxes:
Rated load current:
Active element:
Type of supported
motor:
110 • 240 V AC
50-60Hz
to0,8W
o-35°c
42,5
x
38,25
x
20,3 mm
0
~
50mm,
depth
~
60mm
4,2 A for lamps and resistive loads
1, 7 A for motors with compensated
power factor (inductive loads)
micro-gap relay switch
µ
sing[e-phase AC motors
Supported limit switches type:
electronic and mechanic
Device control:
Radio protocol:
Radio signal power:
Radio Frequency:
Range:
Comp!y with EU directives:
remotely - radio waves
directly - push buttons
Z-Wave
1mW
868,4 MHz EU;
908 ,4 MHz
US;
921,4 MHz ANZ;
869,0 MHz RU;
up to 50 m outdoors
up to 30 m indoors
(depending on building materials)
RoHS 2011/65/EU
LVD 2006/95/EC
EMC 2004/108/EC
R&TIE 1999/5/EC
II. TECHNICAL
INFORMATION
• Controlled by FIBARO system devices er any 2-Wave controller.
• FIBARO Roller Shutter 2 is an extension unit.
• Microprocessor control.
• Active element:
e\ectromagnetic,
micro-gap relay switch.
• The device may be operated by momentary er toggle switches
,
and by dedicated roller blind control switches.
• Connected motor's current and historical power consumption
measured.
• To be installed in wall switch boxes of dimensions allowing for
installation, conforming to provisions of applicable regulations.
111.
SUPPORTED LOADS
FGR-222
110-240
v-
~
w
4,2A
lamp and resistive load
~
@
1,7 A
inductive load
IV.
GENERAL INFORMATION
ABOUT
FIBARO SYSTEM
FIBARO is a wireless smart harne automation system, based on the
Z-Wave protocol
.
All of available devices can be controlled through
a computer (PC or Mac), smartphone Or
tablet:
Devices 3re not only
receivers
,
but ·can also repeat the signal, increasing the Z,.Wave
network's range.
lt
gives advant8ge over tradition.al wireless
systems that require direct link between transmitter and receiver, as
a result the construction ofthe building could affect network's range
negatively.
Every FIBARO network has its unique identification number (harne
ID).
Multiple independent networks can exist in the building without
interfering. Transmission security of FIBARO System is comparable
to wired
systems.
2-Wave technology is the leading solution in smart harne
automation. There is a wide range of 2-Wave devices
that
are
mutually compatible, independently of manufacturer. lt gives the
system the ability to evolve and expand over time. For more
information visit:
www.fibaro.com.
V.
ROLLER SHUTTER INSTALLATION
CAUTION
Read this manual before attempting to install
the devicel Failure to observe recommendations
included in this manual may be dangerous or cause
a violation of the law. The manufacturer, Fiba
r
Group S.A., will not be held responsible for any lass
er damage
resulting
from
not fol!owing
the
instructions of operating manual.
CAUTION
Electrical system of the bui!ding must be protected
with an overcurrent protection (fuse) with a value
not higher than 1 OA.
DANG ER
Oanger of electrocution! All works on the device
may be performed only by a qua1ified and licensed
electrician.
Observe national regulations
.
Faulty
connection or use may result in fire or electric
shock.
DAN GER
Danger of electrocutionl Even when the device is
tumed off, voltage may be present at its terminals.
Any
works
introducing
changes
into
the
configuration of connections or the load must be
always
performed
with disconnected
voltage
(disable the fuse)
.
DANG ER
Any maintenance werk on controlled devices may
be performed only after the power supply has been
disconnected.
CAUTION
Jt's not recommended to operate all of the roller
blinds
simultaneously.
For safety reasons, at least
one roller blind should be controlled
independently,
providing safe escape reute in case of emergency.
CAUTION
Do not connect the device to loads exceeding
recommended values. Connect only in accordance
with the diagram presented in the manual.
lmproper connections may be dangerous.
1. Before installation make sure the voltage supply is
disconnected.
2. Connect the Roller Shutter in accordance with the wiring
diagram presented on Fig. 1 (roller blinds, venetian blinds) or
Fig. 2 (gates ).
3.
Place the device in a switch box.
4.
Arrange the antenna (tips presented below Fig. 3)
5. Turn on the power supply keeping the necessary safety
precautions.
6. lnclude the module into the Z-Wave
network,
observing pt. Vl
description.
7.
lf necessary, calibrate the module, observing pt. IX descripion.
8
Fibaro Roller
@
Shutter
Fig. 1 Roller Shutter wiring diagram
D
sensor
NC
limlt
switches
safetyswitch
NC
Fig.
2 Connecting Roller Shutter to GATE motor
NOTES FOR THE DIAGRAM:
L - terminal for live Jead
N - terminal for neutral lead
S1 - terminal for key no. 1 (has the option of entering the device in
leaming mode)
S2 - terminal for key No. 2
Q1 - output terminal no. 1 for shutter motor
Q2 - output terminal no. 2 for shutter motor
B - service button (used to add or remove a device from the
system)
Flg.3 Installation of Fibaro Roller Shutter in wall switch box.
CAUTION
The device is designed for installation in wall switch
boxes and can werk only with the electrical
connectors compliant with the
relevant
safety
standards.
CAUTION
The switch box must be compliant with the relevant
national safety standards and lts depth should not
be less than
60mm.
WARNING
Fibaro Roller Shutter is dedicated to operate with
AC powered electric
motors.
Connecting the device
directly to DC powered motors may result in them
being
damaged.
WARNING
lt is recomended to monitor regulary operation of
Fibaro Roller shutter in all
modes.
In case of gate
control mode device, motor limit switches, infrared
barriers and emergency stop should be monitored
and maintained regu!ary .
NOTE
A push button connected
io
S1 terminal operates
the Q1
output,
while the push button connected to
S2 terminal operates the Q2 output. lt's recommen-
ded to connect an UP button to S1 terminal and a
wire, responsible of up movement, to Q1 output
terminal.
Respee;tively,
a DOWN button should be
connected to S2 terminal and
_
a
wire,
responsible for
down
movement,
to 02
output
terminal.
TIPS FOR ARRANGING THE ANTEN NA
1. Locate the antenna as far from metal e"lements as possible
(connection wires, bracket rings, etc.) in order to prevent
interferences.
2. Metal surfaces in direct vicinity of the antenna (e.g. metal switch
boxes, door frames) may impair radio signal reception!
3.
Do not cut or shorten the
antenna.
lts length is perfectly
matched to the band in which the system operates.
VI.
Z •WAVE NETWORK
INCL
USION
Fibaro Roller Shutter may be included into the 2-Wave network via
the 8-button or a push button connected to the S1 terminal. In
addition,
the module may be included in auto inclusion mode, by
simply connecting the power
supply.
Automatie 2-Wave network inclusion:
1) Make sure the power supply is disconnected and a Roller Shutter
is located within a direct 2-Wave network's main controller
communication range.
2) Set the main controller into the learn mode (see main controllers
operating
manual).
3) Connect the power supply to include the
Roller
Shutter in auto
inclusion mode.
4) Fibaro Roller Shutter will be automatically detected and included
into the Z-Wave network.
To disable the auto inclusion mode, press the B-button
briefly,
after
connecting the module to the power supply.
Manual Z-Wave network lnclusion:
1) Connect the power
supply.
2) Set the main controller into the leam mode (see main controllers
operating
manual).
3) Triple click the B-button or a push button connected to the S1
terminal.
4) Fibaro
Roller
Shutter will be detected and included into the
2-Wave
network.
VII.
Z-WAVE NETWORK EXCLUSION
1) Make sure the module is connected to the power
supply.
2) Set the main controller into the leam mode (see main controllers
operating
manual).
3)
Triple
click_
the B-button or a push button connected to the S1
terminal.
VIII- ROLL
ER SHUTTER
RESET
Reset procedure clears the
modules'
EPROM memory, including all
information about the Z-Wave network controller, calibration and
power consumption
data.
1) Make sure the module is connected to the power supply.
2) Press and hold the 8-button for
ca.
14 seconds.
3) LED indicator will glow
yellow.
4) Release the 8-button and press it again, briefly.
5) The Roller Shutter memory is now empty.
6) The module goes into the auto inclusion mode, until any button
is pushed.
[IJ
CAUTION
Memory reset does not remove the module from
the Z-Wave network main controller's memory.
Prior to memory reset it's recommended to exclude
the module from the 2-Wave netvvork.
TIP
Aftermemory
reset,
the Roller Shutter goes into the
auto inclusion mode and waits to be included into
the Z-Wave
network.
To exit the auto inclusion
mode press the B-button
briefly.
IX_
POSITIONING
CALIBRATION
Calibration is a process during which a Roller Shutter learns the
position of the limit switches and a motor characteristic. Calibration
is mandatory in order for the Roller Shutter to correctly recognize a
roller blind
position.
The procedure consists of an
automatic,
full
movement between the limit switches (up, down, and up again).
There are separate procedures of calibrating roller blind and slats
(venetian blind) positloning
.
Each time the calibration requires the
completion of a full cycle (up and
down).
ROLLER BLIND POSITIONING CALIBRATION
There are 5 procedures of calibrating a Fibaro Roller Shutter to
choose from
.
Each one gives the same results and the user may
choose which one to execute.
A. Calibration through a Fibaro Horne Center 2 interface
1) Make sure the module is connected to the power
supply,
according to Fig.1
2) lnclude the module into the 2-Wave
network,
according to section
VI of
instructions.
3) In Horne Center 2 interface choose Fibaro Roller Shutter's
advanced settings.
4) Click CALi BRATE buttin in the devices advanced settings !ab.
5) Roller Shutter performs the calibration
process,
completmg full
cycle -
up,
down and up again.
6) Using an interface test
whether
the positioning works correctly.
B. Calibration through the 2-Wave network
1) Make sure the module is connected to the power
supply,
according to Fig.1
2) lnclude the module into the Z-Wave tietwdrk, according to section
VI of instructions.
.
3)
Set the parameter 29 value
tb
1.
.
4) Roller Shutter performs the calibration process, completmg full
cycle -
up,
down and up again.
5) The pararneter 29 value will be automatically set to
0.
6) Using an interface test whether the positionlng works correctly.
c.
Calibration through the switch keys
1) Make sure the module is connected to t~e power supply,
according to Fig.1, and to the switch keys as weil (S1 and S2
inputs).
.
.
2) lnclude the module into the 2-Wave netvvork, accordrng to sect1on
VI of instructions.
3) Press and hold the switch key connected to S1 or S2 input
terminal and release it after at least 3
seconds.
4) Press and hold the same switch key again
,
and release
it
after 3
seconds.
5) New press and hold the same button, for 3 seconds
,
for the 3rd
time.
6) After pressing and releasing the button for the third
time,
automatic ca libration sequence will
start.
7) Roller Shutter performs the calibration process, completing full
cycle - up, down and up again.
D.
Calibration through Menu (B-button)
1) Make sure the module is connected to the power supply,
according to Fig.1
2) lnclude the module into the 2-Wave
network,
according to section
VI of instructions.
3) Press and hold the 8 -button for ca. 6 seconds.
4)
LED will glow blue.
5) Release the 8-button and press it again
, briefly.
.
6) Roller Shutter performs the calibration process
,
completing full
cycle -
up,
down and up again
.
E. Calibration through- a
Fibar
Command Class control
frame.
lt's possible to force the calibration process execution through
sending a Fibar Command Class control frame through a 2-Wave
network main controller.
NOTE
[IJ
To abort the calibration process press any key
(connected to S1 or S2) or send a STOP control
frame through the 2-Wave network
controller.
In
Gate Controller mode the calibration process will
be aborted after disconnecting the S2 terminal.
CALIBRATING SLATS POSITIONING
IN VENETIAN BLINDS
Apart
·
from calibrating the roller blind position
,
it's possible to
calibrate the position of venetlan blinds slats. After correct
calibration
,
in case of venetlan blinds
,
it's possible toset the position
between the limit switches, as weil as the slats
angle.
By
defau1t,
time of full turn of the slats is set to 1,5 seconds. lf necessary, it can
be modified following below
instructions.
1) Make sure the module is connected to the power supply,
according to Fig.1
2) lnclude the module into the Z-Wave network, according to section
VI of instructions.
3) Calibrate the Roller Shutter, according to the instructions
provided in sections IX.A,
IX.B,
IX.C, IX.D or IX.E.
4) Set the parameter 10 value to 2 or choose in HC2
interface:
Device Type - Venetian Blind
5) Another device
icon,
responsible for slats operation, will show
up in Horne Center 2 interface. In case
of
any other 2-Wave
netvvork controllers managing the slats position is achieved
through pressing and holding a switch key (up or down).
6) By default, time of transition between extreme positions is set to
1 500 ms (1,5 seconds).
7) Turn slats between extreme positions. lf after full cycle a blind
starts moving up or down, then parameter's 12 value must be
modified,
e.g.
to 1 OOOms (1 second). Correctly configured
slats should not force
_
t he blind to move up or
down.
CAUTION
Roller Shutter needs to be calibrated to work with
any given motor.
CAUTION
In Venatian Blind mode, slats need to be calibrated
to werk with any given
motor.
CAUTION
Venetian blind slats may be only operated by
momentary
switches.
X
.
OPERAT
ING
T HROU
GH THE
Z
-WAVE
NETWORK
After including into the 2-Wave
network,
Fib.
a ro Roller Shutter will
be presented in a Horne Center 2 interface as a roller blind icon (see
fig. below). After choosing Venetian Blinddevice type
,
a second icon
will show
up,
responsible.
for managing slats
posltion.
Fig. 4 Roller Shutter icons in Horne Center Interface
User can choose from the following operating
modes:
1. Roller Blind Mode, without positioning
2.
Roller Blind Mode, with positioning
3.
Venetian Blind Mode
4. Gate Mode, without positioning
5.
Gate
Mode,
with positioning
After choosing one of the above operating
modes,
device will be
represented in Horne Center 2 interface by icons shown in Fig.4. In
addition, each operating mode affects certain parameters settings:
1) Roller blind without positioning (parameter 10 sei to
O)
2)
Roller blind with positioning (parameter 10 sei to 1)
3) Venetian blind (parameter 10 set to
2;
parameter
13,
set to 2)
4) Gate without positioning (parameter 10 set to
3;
parameter 12 sei
to
O;
parameter 17 sei to 0)
5) Gate with positioning (parameter 10 set to 4; parameter 12 set to
O;
parameter 17 sei to 0)
NOTE
Above operating modes and their default settings
are modifted automatically only in Horne Center 2
controller.
ln
case
of the 2-Wave
network
controllers
from
other
manufacturers,
these
settings need tobe manua!ly adjusted (see section
XVIII).
Opening / Closing a blind is acheved through moving a slider or
pushing a button shown in Fig. 4.
In Venetian Blind mode, setting slats angle is achieved through
moving a stider or pushing a button shown in
Fig. 4.
XI.
MANUAL
OPERATION
Flbaro Roller Shutter allows for connecting push buttons to S1 and
S2 terminals. These may be momentary or toggle switches,
altematively. Push buttons are responsible for managing the blind's
movement.
Using momentary switches:
Clicking
A
button connected to S1
terminal,
initiales up
movement.
Clicklng
.....
button connected to S2 terminal, initiates down
movement.
lf the blind is moving, each
click,
of any button, will stop the
movement. In addition a button click sends a command frame to 1-st
association group devices.
In case of venetian blinds, it's posslble to manage the slats
angle.
Operating Mode - Venetian Blind, or Parameter 10 value set to 2.
Holding
A
connected to S1 terminal initiales slats rotation
up.
Holding
.....
connected to S2 terminal initiales slats rotation
down.
In addition a button hold sends a Fibar Command Class control
frame to 11-nd association group devices.
Using toggle switches:
Changing
J/J;..
swltch key position, connected to S1 terminal
,
initiates up movement.
Changlng
.....
switch key
position,
connected to S2 terminal,
initiales down movement.
Choosing a middle position stops the
blind.
XII.
ASSOCIATIONS
Through an association Fibaro Roller
Shutter
may control another
·
2-Wave network
device,
e.g. another Roller Shutter, Wall Plug,
Dimmer, Relay
Switch,
RGBW Controller.
&
NOTE
Assoc1at1on
allows
for
direct communicaUon
between 2-Wave network dev1ces Marn controller
does not take part
in
such commumcatton
Advertisement
