Advertisement
2.56"
(65 mm)
.83"
(21 mm)
2.00"
(51 mm)
ELECTRICAL SPECIFICATIONS
Nominal Range: 150A
Measurement Range: 0.1 to 150A
Transformation Ratio: Voltage output
Output Signal: 10mV/A
Accuracy and Phase Shift*:
Accuracy:
3% Reading ± 200µV
0.1 to 1A:
2% Reading ± 200µV
1 to 20A:
1% Reading
20 to 80A:
3% Reading
80 to 150A:
150 to 200A: 7% Reading
.73"
(18.5 mm)
Tactical
Barrier
(keep hands below
this barrier)
Black
Red
.1.18"
(30 mm)
Phase Shift:
0.1 to 1A:
Not Specified
3°
1 to 20A:
2°
20 to 80A:
3°
80 to 150A:
150 to 200A: 4°
(*Reference conditions: 18°C to 28°C, 20 to 75%
RH, external magnetic field <40 A/m, 48 to 65 Hz
sine wave, distortion factor less than 1%, no DC
component, no external current carrying conductor,
test sample centered.)
Load impedance > 1 M.
Frequency Range: 40 to 10kHz
Limit Operating Conditions:
200A permanently to 1kHz;
Derating above 3kHz: 200A x (1/0.333F), F in kHz
www.
Shop for AEMC products online at:
Crest Factor:
3 @ 150A peak max with an error
(due to CF) of 3%
Overload: 240A for 10 min ON, 30 min OFF
Working Voltage: 600Vrms
Common Mode Voltage: 600Vrms
Influence of Adjacent Conductor:
< 15mA/A at 50 Hz
Influence of DC on AC signal:
DC Current < 10A, < 10%
Influence of Conductor Position in Jaw:
0.5% of mV output @ 50/60 Hz
Influence of Frequency:
40 Hz to 1 kHz: 5% of mV output
1 kHz to 10 kHz: 15% of mV output
Influence of Load:
< 3% of mA output from 40 Hz to 1 kHz
< 12% of mA output from 1 kHz to 10 kHz
Influence of Temperature:
200 ppm/°K, or 0.2% of mV output per 10°K
Influence of Humidity (10 - 90% RH):
0.2% of mV output per 10°K @ 18°C to 28°C
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 131°F (-10° to +55°C)
Storage Temperature:
-40° to 158°F (-40° to +70°C)
Operating Relative Humidity:
10-35°C 85% RH
(without roll-off above 35°C)
Maximum Cable Diameter:
One Ø 0.78" (20mm), bus bar 20 x 5mm
Case Protection:
IP 40 (IEC 529)
Drop Test:
Test per IEC 68-2-32:
1.0m drop on 38 mm of Oak on concrete.
Mechanical Shock:
Test per IEC 68-2-27
Vibration:
Test per IEC 68-2-6
ShopAEMC
.com
1.877.766.5412
Dimensions:
5.47 x 2.00 x 1.18" (139 x 51 x 30mm)
Weight:
180 g (6.5 oz)
Polycarbonate Material:
Jaws: Polycarbonate with 10% fiberglass charge,
Red UL 94 V0
Case: Polycarbonate 920A Gray
Opening Operations - Life:
> 50,000
Output:
MN352: Two standard safety banana jacks (4mm)
MN353: Double/reinforced insulated 5 ft (1.5m)
lead with safety 4mm banana plug
SAFETY SPECIFICATIONS
E192383
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of
the handle conforms to IEC 1010-2-32.
Common Mode Voltage:
600V Category III
Pollution Degree 2
Dielectric Strength:
5550 V, 50/60 Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge
IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60 Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe MN352 .......... Cat #2116.26
AC Current Probe MN353 .......... Cat #2116.27
Both models include a user manual and a
product warranty and registration card.
Accessories:
Leads, set of 2, 5 ft safety
(1000V) for Model MN352 ............ Cat #2111.29
Banana plug adapter
(to non-recessed plug) ................ Cat #1017.45
Advertisement
