Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Young 09101
Summary of Contents for Young 09101
- Page 1 METEOROLOGICAL INSTRUMENTS INSTRUCTIONS WIND MONITOR - SE MODEL 09101 R.M. YOUNG COMPANY 2801 AERO PARK DRIVE, TRAVERSE CITY, MICHIGAN 49686, USA TEL: (231) 946-3980 FAX: (231) 946-4772 WEB: www.youngusa.com P/N: 09101-90 REV: I111215...
-
Page 2: Initial Checkout
INITIAL SETUP Resolution: 1 degree Threshold: 1.1 m/s (2.5 mph) @ 10° displacement The 09101 has been calibrated at the factory and requires no additional adjustments. Operation is configured by onboard Delay distance: 1.3 m (4.3 ft) jumpers and software commands. -
Page 3: Serial Protocols
4 OUT 5 IN 9600 baud 4 OUT 5 OUT When NCAR protocol is set via jumper J1, the 09101 defaults to bussed mode when powered up. A sequence of three ESC codes Knots 6 IN 7 IN (ASCII 27) toggles the 09101 between bussed and interactive... -
Page 4: Voltage Outputs
0-5 VDC for 0-540° range. Wind speed voltage output is 0-5 VDC for 0-100 meters per Where “aa” is the 09101 address in hex, 00-FF; “c” is a single second. ch a r a c te r p s e u d o - c h e c k s u m; a n d < E O T > i s t h e e n d - o f - transmission character (ASCII 4). -
Page 5: Maintenance
Insert edge of a pocket knife under bearing flange and lift it with a wind speed standard. Contact the factory or your YOUNG out. supplier to schedule a NIST (National Institute of Standards &... -
Page 6: Emc Compliance
10. ALIGN VANE Liability is limited to repair or replacement of defective item. A copy of the warranty policy may be obtained from R. M. Young Company. a) Connect sensor to indicator. b) Install sensor on vane angle fixture (Young Model 18112 or equivalent) with junction box at 180°... -
Page 7: Cable & Wiring Diagram
CABLE & WIRING DIAGRAM MODEL 09101 WIND MONITOR-SE 09101-90(I) Page 6... - Page 8 BEARING REPLACEMENT & POTENTIOMETER ADJUSTMENT 09101-90(I) Page 7...
- Page 9 4-40 x 5/16 SCREW (3) 05129 BAND CLAMP 05121E-10 (INCL. W/ 05121E, 05128B) JUNCTION BOX COVER 05128B ORIENTATION RING R. M. YOUNG COMPANY 2801 Aero Park Drive , Traverse City, Michigan 49686 U.S.A. 09101-90(I) TEL (231) 946-3980 FAX (231) 946-4772 Page 8...
-
Page 10: Calibration Accessories
Calibration Accessories Model 18802 Anemometer Drive Model 18112 Vane Angle Bench Stand Model 18331 Vane Torque Gauge Model 18212 Vane Angle Fixture-Tower Mount Model 18310 Propeller Torque Disc Model 18301 Vane Alignment Rod 09101-90(I) Page 9... -
Page 11: Specifications
CUP-WHEEL TORQUE DISC ............18312 VANE TORQUE GAUGE ..............18331 VANE ALIGNMENT ROD ..............18301 Specifications subject to change without notice. Copyright © 2000 R.M. Young Company, Printed in U.S.A. 11/00 R.M. YOUNG COMPANY 2801 Aero Park Drive Traverse City, Michigan 49686 USA TEL: (231) 946-3980 FAX: (231) 946-4772 E-mail: met.sales@youngusa.com...
Need help?
Do you have a question about the 09101 and is the answer not in the manual?
Questions and answers