Related Manuals for General GLDM25
Summary of Contents for General GLDM25
- Page 1 G L D M 2 5 L A S E R D I S T A N C E M E A S U R E R I N S T R U C T I O N M A N U A L...
- Page 2 S A F E T Y Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place for future reference. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. WARNING: Read and understand › Do not place the laser in a position all instructions.
-
Page 3: Item Checklist
I T E M C H E C K L I S T Please ensure the following items are included with your laser distance measurer. If anything is missing please contact your retailer. General GLDM25 Carry pouch Alkaline batteries... -
Page 4: Product Overview
P R O D U C T O V E R V I E W L AS ER ME AS URER F RON T Laser emitter LCD screen Control panel... - Page 5 L A S E R ME A S U R E R B ACK Battery compartment...
-
Page 6: Control Panel
CONT R O L PANEL Read (laser emission on) Multi-function Benchmark / unit reset Power off / clear... - Page 7 D I S PL AY S C RE E N Battery level Pythagorean measurement mode Measurement mode Measurement mode Laser emission on Angle measurement mode Benchmark reference point Length measurement mode Continuous measurement mode Previous measurement display Major measurement display Unit...
- Page 8 U S I N G Y O U R L A S E R M E A S U R E R PO W ER S U P P LY › The General GLDM25 is supplied with two 1.5v AAA alkaline batteries. › To replace batteries remove the battery door at the back of the device.
-
Page 9: Backlight Setting
BACKLIGHT SETTING Press and hold the unit reset / backlight button to turn the backlight on or off. REFERENCE POINT SETTING To cycle between the benchmark reference points press the benchmark / unit reset button. There are two reference points: top or bottom. M EA S UR EM E N T SINGLE MEASUREMENT ›... -
Page 10: Area Measurement
AREA MEASUREMENT a) Press and hold the multi-function button. A rectangle will appear on the display screen with one edge flashing. b) Press the read button to measure the first edge (length). c) Press the read button to measure the second edge (width). d) Area will be calculated automatically with results shown on the display screen. - Page 11 PYTHAGORAS MEASUREMENT To calculate the unilateral distance of a triangle pythagorean mode can be used. When taking measurements of the triangle, ensure the length of the right side is shorter than the length of the hypotenuse. If not, the instrument will display an error signal.
- Page 12 2. Calculate the hypotenuse of a right angle triangle Press and hold the multi-function button to enter area mode, then press three times to enter pythagorean mode. A triangle will appear on the display screen with the bottom line flashing. Follow the instructions displayed on the screen as follows: a) Press the read button to measure the length (a) of the rectangular side.
- Page 13 3. Calculate the third side of a triangle Press and hold the multi-function button to enter area mode, then press four times to enter pythagorean mode. A triangle will with appear on the display screen with the hypotenuse flashing. Follow the instructions displayed on the screen as follows: a) Press the read button to measure the length (a).
- Page 14 4. Calculate partial length of a right angle triangle Press and hold the multi-function button to enter area mode, then press five times to enter pythagorean mode. A triangle will with appear on the display screen with the hypotenuse flashing. Follow the instructions displayed on the screen as follows: a) Press the read button to measure the length (a) of the hypotenuse.
-
Page 15: Other Functions
OTHER FUNCTIONS ADDING AND SUBTRACTING MEASUREMENT Addition a) Take the first reading by pressing the read button. b) Press the multi-function button. A “+” symbol will appear on the display screen. c) Take the second reading by pressing the read button. The values will be added automatically with the results shown on the display screen. -
Page 16: Care And Maintenance
C A R E A N D M A I N T E N A N C E › Inaccurate measurement results may occur in harsh environments such as strong sunlight, excessive temperature fluctuations, weak reflective surfaces or low battery. ›... -
Page 17: Troubleshooting
T R O U B L E S H O O T I N G ERROR CODE CAUSE & SOLUTION Signal is too weak. ERR1 Measure target locations that have stronger reflecting surfaces. Signal is too strong. ERR2 Measure target locations that have weaker reflecting surfaces. Battery voltage too low. -
Page 18: Warranty
W A R R A N T Y The General GLDM25 comes with a 3 year manufacturers warranty. AUSTRALIA "Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. -
Page 19: Specifications
S P E C I F I C A T I O N S Specifications GLDM25 Product code 70083 Accuracy ±2mm Minimum measurement range (top reference point) 0.05m Maximum measurement range Minimum unit displayed 0.05mm Measurement unit options m/in/ft Continuous measurement function... - Page 20 www.spoton.com.au...