Table of Contents
Advertisement
cleanup
Do not use gasoline to clean the sprayer.
Special cleanup instructions for use with
flammable solvents:
• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal
container, place it into an empty five gallon container, then
flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
IMPORTaNT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material
to build up, seriously affecting the performance of the unit.
always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.
1. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent (refer to recommendations of the material
manufacturer). An example of the appropriate solvent is
water for latex paint.
4. Place the return hose into a metal waste container.
5. Move the PRIME/SPRAY valve down to
the PRIME position.
NOTE: hold the return hose in the waste
container when moving the PRIME/
SPRay valve to PRIME in case the
sprayer is pressurized.
6. Turn the unit on and set the pressure to
Turbo PulseClean by turning the pressure
control knob to its CLEAN position in the
red zone.
7. Allow the solvent to circulate through the
unit and flush the paint out of the return
hose into the metal waste container.
8. Turn the unit off by moving the pressure control knob to
the OFF position in the black zone.
9. Move the PRIME/SPRAY valve up to its
SPRAY position.
10. Turn the unit on and set the pressure to Turbo
PulseClean by turning the pressure control
knob to its CLEAN position in the red zone.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
11. Trigger the gun into the metal waste container until the
paint is flushed out of the hose and solvent is coming out
of the gun.
12. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
NOTE: For long-term or cold weather storage, pump
mineral sprits or Pump Saver Plus through the
entire system.
13. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual.
14. Unplug the sprayer and store in a clean, dry area.
IMPORTaNT: Do not store the unit under pressure.
© Titan Tool Inc. All rights reserved.
cleaning the Spray Tip
1. Flush the gun with solvent immediately after the work is
completed.
2. Oil the sliding pins to prevent them from seizing up.
Maintenance
General Repair and Service Notes
The following tools are needed when repairing this sprayer:
Phillips Screwdriver
Needle Nose Pliers
Adjustable Wrench
Rubber Mallet
Flat-blade Screwdriver
1. Before repairing any part of the sprayer, read the
instructions carefully, including all warnings.
IMPORTaNT: Never pull on a wire to disconnect it. Pulling
on a wire could loosen the connector from the wire.
2. Test your repair before regular operation of the sprayer
to be sure that the problem is corrected. If the sprayer
does not operate properly, review the repair procedure to
determine if everything was done correctly. Refer to the
Troubleshooting section to help identify other possible
problems.
3. Make sure that the service area is well ventilated in
case solvents are used during cleaning. Always wear
Min.
PSI
(Bar)
protective eyewear while servicing. Additional protective
equipment may be required depending on the type of
cleaning solvent. Always contact the supplier of solvents
Max. PSI
On/Off
(Bar)
for recommendations.
4. If you have any further questions concerning your TITAN
Airless Sprayer, call TITAN:
Technical Service (U.S.) ....................... 1-800-526-5362
7
Do not attempt to clean the tip with your finger.
Do not use a needle or other sharp pointed
instrument to clean the tip. The hard tungsten
carbide is brittle and can be chipped.
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. always unplug the sprayer
before servicing!
3/8" Hex Wrench
5/16" Hex Wrench
1/4" Hex Wrench
3/16" Hex Wrench
5/32" Hex Wrench
Fax ................................................ 1-800-528-4826
Advertisement
Table of Contents
