Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Huffy Manuals
  4. Fitness Equipment
  5. 211948C
  6. Owner's manual

Huffy 211948C Owner's Manual

Portable system
Hide thumbs

Advertisement

Quick Links

Download this manual
© COPYRIGHT 2000 by HUFFY SPORTS
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
REQUIRED TOOLS AND MATERIALS:
• Two People
• Tape Measure
• Wood Board (Scrap)
• Wrenches: (One) 3/8", 5/16", (Two) 7/16", 1/2", 9/16",
3/4", or Large and Small Adjustable Wrenches
• Sawhorse or Support Table
• Step Ladder 8 ft. (2.4 m)
• Garden Hose or Sand (225 lb.) (102 kg)
• Hammer
• Tape
• Phillips Screwdriver
1
01/04
P/N 211948C

Advertisement

loading
Need help?

Need help?

Do you have a question about the 211948C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huffy 211948C

Summary of Contents for Huffy 211948C

  • Page 1 • Garden Hose or Sand (225 lb.) (102 kg) • Hammer • Tape • Phillips Screwdriver For Canada: 1-800-284-8339, For Australia: 1-800-333 061 Internet Address: http://www.huffysports.com REQUIRED TOOLS AND MATERIALS: 3/4”, or Large and Small Adjustable Wrenches 01/04 P/N 211948C...

  • Page 2: Before You Start

    Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. P/N 211948C 01/04...
  • Page 3 • Use Caution when moving system across uneven surfaces. System may tip over. • Use extreme caution if placing system on sloped surface. System may tip over more easily. In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 201246 2/99 01/04 P/N 211948C...

  • Page 4: Safety Instructions

    • If technical assistance is required contact Huffy Sports. • Adult supervision is recommended when adjusting height. Most injuries are caused by misuse and/or not following instructions. P/N 211948C 01/04 PROPERTY DAMAGE AND WILL VOID WARRANTY. Use caution when using this system.
  • Page 5 WARRANTY CARD: Please remember to complete your product registration form either on-line at: www.huffysports.com or mail-in the enclosed postcard. For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. 01/04 P/N 211948C...
  • Page 6 Get to know the basic parts of your basketball system... FRONT BACKBOARD ELEVATOR SYSTEM POLE STRUT BASE WHEEL CARRIAGE ASSEMBLY P/N 211948C 01/04...
  • Page 7 204290 206990 Reinforcement Bracket 200628 Wheel Axle, 11 3/4 Long 200627 Wheel Carriage 203217 Carriage Bolt, 5/16-18 x 1 1/2 Long 200874 Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long 201642 Spacer .530 I.D. x.63 O.D. x .63 Long 01/04 P/N 211948C...
  • Page 8 Item #18 (2) Item #27 (4) HARDWARE IDENTIFIER (NUTS) Item #34 (4) Item #10 (3) Item #38 (6) Item #14 (11)* Item #32 (1) Item #15 (1) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) P/N 211948C 01/04...
  • Page 9 Item #13 (11) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #37 (8) Item #43 (12) Item #6 (2) ITEMS NOT USED WITH THIS MODEL Item #67 (2) Item #68 (2) * You may have extra parts with this model. 01/04 P/N 211948C...

  • Page 10: Section A: Assemble The Base

    TOOLS REQUIRED FOR THIS SECTION Wrenches (2) 1/2” AND (2) 9/16" AND/OR Socket Wrenches and Sockets 9/16” 1/2” P/N 211948C 01/04 HARDWARE USED IN THIS SECTION Item #33 Item #27 Item #18 Item #10 Socket Extension...
  • Page 11 Install wheel axle (64) through wheel carriage (65) and install wheels (5) onto wheel axle (64) with spacers (6) as shown. Secure wheel bracket as shown, a deep socket is recommended. IMPORTANT!: DO NOT OVER TIGHTEN Mark pole sections with tape as shown. MIDDLE 5" (13 cm) BOTTOM 5" (13 cm) 01/04 P/N 211948C...
  • Page 12 (3) together as shown until they no longer moved toward taped reference mark. NOTE: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. P/N 211948C 01/04 WOOD SCRAP (NOT SUPPLIED) WOOD SCRAP (NOT SUPPLIED)
  • Page 13 Insert pole assembly into tank assembly as shown. Secure pole assembly with upper pivot bracket (9) and lock nut (10). WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 01/04 P/N 211948C...
  • Page 14 TIGHTEN BOLT (9) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. Secure base struts (11) to base using bolt (16), washers (13), and nut (14). P/N 211948C 01/04 Rotate the non-secured ends of base struts (11) as shown. NOTE:...
  • Page 15 (25) as shown. Attach handle bar (20) to wheel bracket assembly using nuts (14) as shown. Attach wheel bracket assembly to base assembly using bolt (19), washers (13), and nut (10) as shown. 01/04 P/N 211948C...
  • Page 16 Carefully reposition entire assembly as shown. Insert bolts (66) through plastic handle assembly, handle bar (20), and attach nuts (14) as shown. Tighten completely. P/N 211948C 01/04 Attach front of plastic handle (26) to back of plastic handle (23) around handle bar (20) using self- tapping screws (27) as shown.
  • Page 17 (14) as shown. NOTE: Assemble lanyard (27) to locking pin (28) as shown. IMPORTANT!: Loop end of pin lanyard (59) over carriage bolt (39) as it passes through the pole mount bracket (53) during this assembly. 01/04 P/N 211948C...
  • Page 18 NOTE: Holes in adjustment rod allow for either rear access or side access. P/N 211948C 01/04 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark...

  • Page 19: Section B: Attach The Backboard

    Wrenches (2) 1/2”, (2) 9/16" AND 3/4" Item #36 AND/OR Item #37 Item #43 Item #30 Socket Wrenches and Sockets Item #33 Item #31 Item #32 Item #34 Socket Extension Item #14 Item #38 1/2” 9/16” 3/4" 01/04 P/N 211948C...
  • Page 20 Install spacers (30) onto backboard brackets (29) with bolts (31, 33) and lock nuts (32, 34) as shown. Assemble lower elevator tubes (35) as shown. Tighten completely. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. P/N 211948C 01/04...
  • Page 21 IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Do not use washers here on spring return style rim. Bend bracket (29) to line up with holes in backboard and secure. Note Assemble upper elevator tubes(40) to backboard brackets(29) as shown. 01/04 P/N 211948C...
  • Page 22 (38). NOTE: Before going onto the next step, set adjustment system to the 10’ (3.05m) setting. P/N 211948C 01/04 Insert bolt (36) through the left side of the upper elevator tube (40), then stretch spring (42) onto bolt (36).
  • Page 23 2. Rotate handles forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Reattach ground restraint and check system for stability. 201253 2/99 01/04 P/N 211948C...
  • Page 24 ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. P/N 211948C 01/04 NET INSTALLATION Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown.
  • Page 25 SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP 01/04 P/N 211948C...