Verlängerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Große Schrauben zur Probe in die großen Löcher der Verlängerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese vorsichtig in einer Kreisbewegung hin- und herbewegen, um eventuelle Farbrückstände aus den Bohrungen zu entfernen. P/N 211696 07/03 any excess paint from holes if necessary.
Page 3
(Do not use salt.) • Use extreme caution if placing system on sloped surface. System may tip over more easily. In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 201241 2/99 07/03 P/N 211696...
• If technical assistance is required contact Huffy Sports. • Adult supervision is recommended when adjusting height. Most injuries are caused by misuse and/or not following instructions. P/N 211696 07/03 PROPERTY DAMAGE AND WILL VOID WARRANTY. Use caution when using this system.
Page 5
WARRANTY CARD: Please remember to complete your product registration form either on-line at: www.huffysports.com or mail-in the enclosed postcard. For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. 07/03 P/N 211696...
Page 6
Get to know the basic parts of your basketball system... FRONT BACKBOARD POLE STRUT BASE WHEEL CARRIAGE ASSEMBLY P/N 211696 07/03...
Page 7
Label, Height Adjustment and Moving 203617 Plug Cap 201568 Anchor, T-Strap NOTE: Hardware kit is designed for more than one style of basketball system. Not all hardware will be used. * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 07/03 P/N 211696...
Page 8
Item #36 (1) HARDWARE IDENTIFIER (NUTS & SPRINGS) Item #20 (8)* Item #16 (6) Item #32 (5) Item #43 (1) Item #12 (3) Item #41 (1) Item #23 (3) * You may have extra parts with this model. P/N 211696 07/03...
TOOLS REQUIRED FOR THIS SECTION (not actual size) 9/16” and 1/2” Item #9 AND/OR Item #18 9/16” and 1/2” Item #17 Item #8 Item #14 Item #19 Item #12 Item #20 Item #21 (2) Item #16 Item #11 P/N 211696 07/03...
Page 11
Remove contents from tank. Correctly identify each pole section as labeled. UPPER BOTTOM MIDDLE 07/03 P/N 211696...
Page 12
Secure bottom pole (7) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. IMPORTANT!: THE SPACER (11) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE P/N 211696 07/03 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS...
Page 13
(16) with supplied allen wrench (21) as shown. Item #21 (2) Attach middle section of pole (6) onto bottom section of pole (7). Align holes in middle pole (6) with hole pattern on bottom pole (7). 07/03 P/N 211696...
Page 14
Secure poles by attaching bolt (17), washers (14), and sleeve nuts (16) as shown. P/N 211696 07/03...
Page 15
Rotate the non-secured ends of base struts (15) as shown. Secure base struts (15) to base using bolts (18), washers (19), and nuts (20). 07/03 P/N 211696...
Page 16
Support pole on sawhorse. Attach upper section of pole (5) to middle section of pole (6) using bolts (17), washers (14), and nuts (16) as shown. P/N 211696 07/03...
Page 17
While still supported on sawhorse attach top section of pole (4) to upper section of pole (5) using bolts (17), washers (14), and nuts (16) as shown. 07/03 P/N 211696...
This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION 3/4", 9/16” and 1/2” AND/OR 3/4", 9/16” and 1/2” P/N 211696 07/03 HARDWARE USED IN THIS SECTION (not actual size) Item #30 Item #18 Item #24...
Page 19
Assemble backboard brackets (25) using spacers (22), bolts (24), and nuts (23) as shown. 07/03 P/N 211696...
Page 20
Attach lower elevator tubes (28) to backboard brackets (25) using spacers (29 & 11), bolts (30) spacers (11) ratchet (31), and nuts (32) as shown. P/N 211696 07/03...
Page 21
(37) to backboard using bolt (18) and nut (20) as shown. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Stretch spring (35) into position with pliers. WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 07/03 P/N 211696...
Page 22
(30), and nut (32) as shown. Support pole on sawhorse. Attach upper and lower elevator tubes (28) to top pole section (4) using bolts (30) and nuts (32) as shown. Attach pole cap (38) as shown. P/N 211696 07/03 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
Page 23
Install reinforcement bracket (40) onto “T” bolt (36) as shown. Install spring (41) onto “T” bolt (36) as shown. Install special nut (43) and washer (42) onto “T” bolt (36). Tighten nut (43) until flush with end of “T” bolt (36). 07/03 P/N 211696...
Page 24
PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. P/N 211696 07/03 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm”...
Page 25
NET INSTALLATION SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP 07/03 P/N 211696...
Page 26
(360 lb./163 kg) and snap tank cap (47) in place. Insert T-strap (48) through slot on back of base as shown. Secure unit to ground by twisting tie down stake (49) into ground and hooking T-strap (48) onto tie down stake (49). P/N 211696 07/03 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE.