Advertisement
Quick Links
LANCOM 1783VA-4G
Quick Reference Guide
Cloud-ready
4
Gigabit Ethernet 10/100/1000
VDSL / ADSL
a
b
c
Please observe the
following when setting
up the device
h
a
For devices to be
operated on the
desktop, please attach
the adhesive rubber
footpads
a
LTE / 4G antennas
Connect the two supplied cellular
Do not rest any objects
a
antennas to the connectors located
on top of the device and
at the device's sides.
do not stack multiple
devices
b
VDSL / ADSL interface*
Use the supplied DSL cable for the
IP-based line to connect the VDSL
LANCOM 1681V
interface and the provider's telephone
a
Keep the ventilation
socket. For more information, please
slots on the side of
contact your Internet service provider.
the device clear of
obstruction
*For operation with over POTS devices
a
In case of wall
please use the DSL cable with the dark
mounting, use the
blue plugs.
drilling template as
Ethernet interfaces
suppliedn
c
Use the cable with the kiwi-colored
connectors to connect one of the
interfaces ETH 1 to ETH 4 to your PC,
an IP telephone or a LAN switch.
a
Rack installation with
Analog interfaces
d
the optional LANCOM
Connect analog terminal devices to
Rack Mount (not
the analog interfaces either directly
supplied)
via RJ11 or with the help of the
enclosed TAE adapter.
TE / NT
NT
Analog2
Analog1
ISDN 1
ISDN 2
a
e
g
d
f
e
Serial interface
Configuring the device via the serial interface
requires a serial configuration cable
(available as an accessory).
f
ISDN interfaces
ISDN 1: Internal (NT) or external (TE) ISDN bus.
This feature is controlled by LCOS.
ISDN 2: Internal (NT) ISDN bus.
A 100-Ohm resistor for line termination is
switchable in LCOS.
g
Power
When connecting the cable to the device, turn
the bayonet connector 90° clockwise until it
clicks into place.
Use only the supplied power adapter.
SIM card slot (bottom side of the device)
h
Release the SIM-card holder and lever it
upwards. Slide the SIM card into the guide slot
of the SIM-card holder. Press the holder down
SIM
until it clicks into place.
LANCOM 1783VA-4G
Reset
a
b
c
d
e
f
g
hi
j
a
f
Power
ETH
Off
Device switched off
Off
No networking device attached
Green, permanently*
Device operational, resp. device paired / claimed
Green, permanently
Connection to network device operational, no
and LANCOM Management Cloud (LMC)
data traffic
accessible
Green, flickering
Data transmission
Green / red, blinking
Configuration password not set. Without a
g
configuration password, the configuration data in
4G
the device is unprotected.
Off
Cellular interface disabled
Red, blinking
Charge or time limit reached
Green, permanently
Connection to cellular network active
1x green inverse
Connection to the LMC active, pairing OK, device
Green, flickering
Cellular data transfer
blinking*
not claimed
Orange, permanently
Logon to cellular network successful
2x green inverse
Pairing error, resp.
Orange, blinking
Logging on to cellular network
blinking*
LMC activation code not available
Red, permanently
Hardware error/module unavailable
3x green inverse
LMC not accessible, resp.
Red / green, blinking
SIM card error (PIN)
blinking*
communication error
Red / orange, blinking
Uploading module firmware
b
Online
h
VoIP
Off
WAN connection inactive
Green, permanently
WAN connection active
Off
No SIP accounts defined or VCM is off
Red, permanently
WAN connection error
Green, permanently
All defined and active SIP accounts (outgoing)
registered successfully
c
DSL
Red, permanently
Not all of the defined and active SIP accounts
were registered (possibly still in process)
Off
Interface deactivated
Green, permanently
DSL connection active
Red or green,
Number of currently used lines (connecting or
inverse flashing
connected)
Green, flickering
DSL data transfer
Red, flickering
DSL transfer error
i
VPN
Red/orange, blinking
DSL hardware error
Off
VPN connection inactive
Orange, blinking
DSL training
Green, permanently
VPN connection active
Orange, permanently
DSL sync
Green, flashing
VPN connecting
Green, blinking
DSL connecting
j
d
Reset
Analog
Reset button
Operated e.g. with a paper clip
Off
Interface deactivated
> Short press: Restart the device
Green, permanently
Interface activated
> Long press: Reset the device
Orange, blinking
Incoming call
Green, blinking
Connection active
*) The additional power LED statuses are displayed in 5-seconds rotation if the
e
ISDN
device is configured to be managed by the LANCOM Management Cloud.
Off
Interface deactivated
Green, permanently
D-channel active
This product contains separate open-source software components which are
Green, blinking
ISDN connected
subject to their own licenses, in particular the General Public License (GPL). The
Red, flickering
ISDN transfer error
license information for the device firmware (LCOS) is available on the device's
Red/orange, blinking
ISDN hardware error
WEBconfig interface under "Extras > License information". If the respective
Red, permanently
ISDN connection not enabled
license demands, the source files for the corresponding software components
will be made available on a download server upon request.
Orange, blinking
ISDN connecting
Hardware
Power supply
12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection
Power consumption
Max. ca. 14 W
Environment
Temperature range 0–35 °C; humidity 0–95 %; non-condensing
Housing
Robust plastic housing, rear connectors, ready for wall mounting, Kensington lock; measures 210 x 45 x 140
mm (W x H x D)
Number of fans
One quiet fan
Interfaces
LANCOM 1783VA-4G over ISDN
LANCOM 1783VA-4G over POTS
WAN: VDSL2
a VDSL2 as per ITU G.993.2; profiles 8a, 8b, 8c, 8d,
a VDSL2 as per ITU G.993.2;
12a, 12b, 17a
profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a
a Compatible to VDSL2 from Deutsche Telekom
a ADSL conformity according to: ADSL2+ over POTS
a ADSL conformity according to: ADSL2+ over ISDN
as per ITU G.992.5 Annex A / Annex M with DPBO,
as per ITU G.992.5 Annex B/J with DPBO, ADSL2
ADSL2 over POTS as per ITU G.992.3 Annex A/L,
over ISDN as per ITU G.992.3 Annex B, ADSL over
ADSL over POTS as per ITU G.992.1 Annex A.
ISDN as per ITU G.992.1 Annex B.
a Supports just one virtual connection at a time in
a Supports just one virtual connection at a time in
ATM (VPI-VCI pair)
ATM (VPI-VCI pair)
ETH
4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode. Up to 3 ports can
be operated as additional WAN ports. Ethernet ports can be electrically disabled in the LCOS configuration.
ISDN 1 / ISDN 2
ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS.
According to the settings, connect the light-blue ISDN cable either to the NTBA or the ISDN terminal device.
ISDN 2: Internal (NT) ISDN bus. Use the light-blue ISDN cable to connect the ISDN interface to the ISDN
device.
Analog 1 / Analog 2
Use the cable of your analog devices to connect them with the analog interfaces. If necessary, use the
enclosed adapter.
Serial interface
Serial configuration interface / COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for optional
connection of analog / GPRS modems. Supports internal COM-port server and provides transparent
asynchronous serial-data transfer via TCP.
4G: Ant1, Ant2
Two SMA connectors for the supplied dipole rod antennas (LTE, UMTS), compatible LANCOM AirLancer
antennas for 4G or 3G, or from other manufacturers. Please respect the restrictions that apply in your country
when setting up an antenna system (in particular the antenna gain and transmission power).
WAN protocols
VDSL, ADSL, Ethernet
PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without DHCP), RIP-1, RIP-2,
VLAN, GRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/IPv6 dual stack session), IP(v6)oE
(autoconfiguration, DHCPv6 or static)
ISDN
DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD
Data transmission in cellular networks
Supported standards:
GPRS, EDGE, UMTS, HSxPA, HSPA+, LTE
LTE
Band 1 (2100 MHz), band 3 (1800 MHz), band 7 (2600 MHz), band 8 (900 MHz),
band 20 (FDD800 MHz) with MIMO
UMTS/HSxPA/HSPA+
Band 1 (2100 MHz), band 8 (900 MHz) with diversity
EDGE/GPRS
GSM 900 (900 MHz), DCS 1800 (1800 MHz), PCS 1900 (1900 MHz)
Max. transm. power
+24 dBm
Declaration of Conformity
Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declarati-
on of conformity is available at the following internet address: www.lancom-systems.com/ce/
Package content
Documentation
Quick Reference Guide (DE/EN), Installation Guide (DE/EN)
Cable
1 Ethernet cable, 3 m (kiwi-colored connectors);
for ISDN: 1 DSL cable for an IP-based line, 4.25m, 1 ISDN cable, 3 m (light-blue connectors);
for over POTS: 1 DSL cable, 3 m (dark-blue connectors)
Adapters
2 TAE adapters (RJ11 - TAE)
Antennas
2 LTE / 4G antennas for LTE / UMTS
Power adapter
External power supply adapter (230 V); NEST 12 V / 1.5 A DC/S; barrel connector 2.1 / 5.5 mm bayonet;
LANCOM item no. 111301 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)
Advertisement
