Advertisement
Operation
Warning
To prevent electrical shock, fire, or personal injury:
•
Read these instructions carefully before using the Product.
•
Use the Product only with Fluke test tools that have the type
number 'BC190' specified for charge and operation.
•
Use this Product only as specified.
•
Do not open the Product, it has no user-serviceable parts inside.
•
Do not use the Product around explosive gas, vapor, or in damp
or wet environments.
The power cord connects the power adapter to the mains system. Do
not block access to the power cord and power plug, these must remain
accessible to the user at all times.
The Product is not equipped with a power switch. Disconnect the mains
plug from the mains system when not in use.
In case the power adapter is damaged or any damage is suspected,
disconnect from the mains system and have qualified service personnel
inspect the Product, before reconnecting to the mains system again.
To use:
1.
Connect the mains plug adapter to the universal power cord.
2.
Connect the cable to the Battery Charger/Power Adapter.
3.
Connect the power plug adapter to the mains system.
4.
Connect the dc plug to the instrument.
The Product operates and charges the Fluke instrument from local
line voltage. Any power supply connected to the ScopeMeter test tool
introduces a certain capacitive coupling between the test tool and ground
through the power supply circuitry. This capacitive coupling can affect
ScopeMeter measurements. The BC190/820 main unit is equipped
with dedicated decoupling networks to reduce possible effects of such
capacitive coupling during measurements.
For an optimal decoupling from ground, especially if low-level
measurements are made, it is recommended to work in battery-operated
mode without any power adapter connected. See the ScopeMeter User
Manual for safety information before making any measurements.
Always fully charge the instrument battery before storing the
test tool.
Figure 2. Universal Cable and Mains Plug Set
Note
Specifications
Input
Nominal input voltage ................ 100 Vac to 240 Vac, ±10 %
Input current ............................... 0.35 A at max. load
Nominal input frequency ............ 50/60 Hz ±10 %
Mains inlet .................................. IEC 60320-1 type C14
Output
Output voltage............................ 18 Vdc ±5 %
Output current ............................ 0 mA to 840 mA
Output cable length .................... 2 m (6.5 ft)
Output connector ....................... 5 mm outer diameter, per DIN45232
Output polarity............................ Inner contact negative, outer contact positive
Physical characteristics
Dimensions of main unit............. 79 mm x 149 mm x 49 mm
Housing material ........................ Heat resistant ABS
Color (housing and cable) .......... Black
Weight ........................................ 0.35 kg
IP Rating .................................... IEC 60529:IP40
Environmental
Operating temperature ............... 0 °C to 50 °C (32 °F to 122 °F), up to 90 % rel.
Storage temperature .................. -40 °C to +70 °C, 10 to 95 % rel. humidity
Max. altitude............................... 2000 m (6562 ft) above sea-level
Included accessories
Power cord ................................. Localized power cord with mains plug or
Universal Mains cord ................. Length 1.5 m (5 ft), male to female
Power plug adapters
included...................................... US-style, UK-style, European ('Schuko'),
General
Safety approval .......................... 600 V CAT IV acc. IEC/EN 61010-1 for
EMC compatibility ...................... EN 61326-1; FCC (47 CFR 15)
Symbols
International electrical symbols used on the Product and in this document
are explained below.
Risk of danger. Important information.
Double Insulated
DC (Direct Current)
Hazardous voltage. Risk of electrical shock.
Conformité Européenne
Energy Efficiency level V
This product complies with the WEEE Directive (2002/96/EC)
marking requirements. The affixed label indicates that you must
not discard this electrical/electronic product in domestic household
waste. Product Category: With reference to the equipment types in
the WEEE Directive Annex I, this product is classed as category 9
"Monitoring and Control Instrumentation" product. Do not dispose of
this product as unsorted municipal waste. Go to Fluke's website for
recycling information.
htx02.eps
Conforms to relevant South Korean EMC Standards.
Conforms to relevant North American Safety Standards.
humidity, no condensation
universal cord with set of power plugs
Chinese/Australian, Italian, Swiss, Brazilian
(adapter cord)
Measurement, Control and Laboratory use.
Advertisement
