Cuisinart DGB-800 Quick Reference & Setup Manual

Troubleshooting

PROBLEM CAUSE
The coffeemaker Filter door is not closed
is beeping
Filter basket is not in
place
Coffee grounds and filter
from previous use are
still in filter basket
The brew cycle There is no water in the
will not start water reservoir
Coffee is weaker There are not enough
than usual beans in the hopper
Strength setting
is incorrect
The coffeemaker The hopper may be
is not grinding too full
beans
EMPTY Coffee grounds and filter
appears in LCD from previous use are
display still in filter basket
CLEAN is flashing Coffeemaker needs
on the LCD to be decalcified
when the unit
is turned on
The coffeemaker The water reservoir
will not enter is empty
CLEAN mode
IMPORTANT
Do not throw away. Read before operating your new
Brewing System. Keep for future reference.
These helpful hints are intended to be a supplement to the Instruction Booklet. In order to ensure
safe operation and optimum performance, please read the entire Instruction Booklet.
PG-36700-ESP
SOLUTION
• Check to be sure that all components of the filter compartment
are in place
• Close filter door (you will hear a click if the door is properly shut)
• Open filter door by pressing the filter door release button
• Hook filter basket with cover onto door
• Close filter door (you will hear a click if the door is properly shut)
• Remove filter and used coffee grounds
• Add new filter
• Fill the water reservoir using the water level markings
• Be sure there are enough beans in your hopper for the amount of
coffee you intend to brew
• Check your strength setting — displayed on the LCD screen
• To change your strength setting, press the Strength Control button
• Turn the coffeemaker off and unplug
• Remove some of the beans from the hopper
• Remove filter and used coffee grounds
• Add new filter
• Run a clean cycle – follow the decalcification directions on page
11 of Instruction Booklet
• Fill the water reservoir with decalcification mixture before turning
the coffeemaker on - Follow the decalcification directions on page
11 of Instruction Booklet
Fully Automatic Burr Grind & Brew
Before using your Cuisinart
BE SURE TO REMOVE POLYBAGS FROM CARAFE AND COFFEEMAKER. PLACE CARAFE BACK ONTO
BASE. During the manufacturing process, dust can get trapped in your coffeemaker. We recommend flushing
out the system before brewing your first pot of coffee. Simply follow "Making Coffee with Pre-Ground
Beans," page 10 in the Instruction Booklet. Skip step #1 and be sure to use only water and a paper filter...no
coffee! Once you've done that, brew a pot of real coffee and get ready to enjoy Cuisinart at its best!
1.
Fully immerse the charcoal water filter in cold tap
water and soak for 15 minutes. Flush filter by running
cold tap water through holes in bottom of compartment
for 10 seconds (see complete instructions on page 8 of
your instruction booklet). Insert the filter into the water
filter holder. Open the water reservoir and place filter
holder into the unit.
3.
Open the filter basket door by pressing the
Release button, and insert a paper filter or
permanent filter into the filter basket holder.
Replace the cover, and close door.
5.
Press the ON/OFF button to turn on the coffeemaker.
Select the amount of cups you wish to brew by turning
the Grind Control knob. Select your desired coffee
strength by pressing the Strength button. Your selected
coffee strength will be indicated in the bar on the LCD
display.
© 2017 Cuisinart
™

BEFORE FIRST USE

® Fully Automatic Burr Grind & Brew™ Coffeemaker for the first time:
Quick Reference SETUP
2.
Pour your desired amount of water into the
water reservoir. A water level indicator is
located on the side of the unit.
4.
Remove hopper lid, fill with beans,
and replace the lid.
6.
To start grinding & brewing, press the BREW
button. Once the coffee has finished brewing,
the unit will immediately enter Keep Warm
mode and alert you with a beep.
Coffeemaker
Guide