Table of Contents
Advertisement
Parameter
Value
-INF, -53.0dB–
PreEqH
0.0dB–+10.0dB
PostEqFreq
0–255
-INF, -53.0dB–
PostEqL
0.0dB–+10.0dB
-INF, -53.0dB–
PostEqH
0.0dB–+10.0dB
COMP+DRV
Balance
OFF, 1–255
[CTRL]
INST
*4
CmpBalance
OFF, 1–255
DrvBalance
OFF, 1–255
CmpAttack
0–255
CmpRelease
0–255
CmpThre
-40dB–0dB
-40dB–0dB–
CmpGain
+40dB
1: 1.00, 1: 1.12,
1: 1.25, 1: 1.40,
1: 1.60, 1: 1.80,
CmpRatio
1: 2.00, 1: 2.50,
1: 3.20, 1: 4.00,
1: 5.60, 1: 8.00,
1: 16.0, 1: INF
HARD, SOFT1,
SOFT2, SOFT3,
CmpKnee
SOFT4, SOFT5,
SOFT6, SOFT7,
SOFT8, SOFT9
DrvDrive
0–255
Explanation
Specifies the high-frequency level of
the EQ that is applied before distorting
the sound.
By slightly decreasing the high-
frequency level, you can reduce
the higher-order partials that are
generated when the sound is
distorted.
Specifies the center frequency of the
EQ that is applied after distorting the
sound.
Specifies the low-frequency level of
the EQ that is applied after distorting
the sound.
Specifies the high-frequency level of
the EQ that is applied after distorting
the sound.
Adjusts the overall COMP+DRV effect.
With a setting of 255, the effect is at
100%.
Adjusts the compression effect.
With a setting of 255, the compression
effect is at 100%.
Adjusts the drive effect.
With a setting of 255, the drive effect
is at 100%.
Specifies the time from when the
input exceeds the level specified by
Thre until the volume is compressed.
As you increase the Attack value
(lengthening the time), the sound's
attack is compressed less.
Specifies the time from when the
input falls below the level specified by
Thre until compression stops being
applied.
As you increase the Release value
(lengthening the time), the sound has
more sustain.
Specifies the level at which
compression begins.
Set a lower value for Thre if you want
to apply the effect deeply, or if the
input level is low.
Setting a low level for Thre will also
decrease the output level, so raise the
Gain to make adjustments.
Specifies the output level.
Set this so that the volume is
approximately the same whether
MASTER FX Sw is on or off.
Specifies the compression ratio.
The higher the ratio, the more
compression is applied to levels that
exceed the Thre setting.
If the ratio is set to 1: INF, the sound
will not become any louder than the
level specified by Thre.
Adjusts how compression is applied.
The HARD setting applies compression
abruptly, producing a hard sound.
The SOFT setting applies compression
gently, producing a soft sound.
Adjusts the depth of distortion.
Because increasing the Drive also
increases the output level, make
adjustments by lowering the Level.
Editing an Instrument's Sound (INST Edit)
Parameter
Value
DrvLevel
0–255
DrvHpF
0–255
DrvPreF
0–255
-INF, -53.0dB–
DrvPreL
0.0dB–+10.0dB
-INF, -53.0dB–
DrvPreH
0.0dB–+10.0dB
DrvPstF
0–255
-INF, -53.0dB–
DrvPstL
0.0dB–+10.0dB
-INF, -53.0dB–
DrvPstH
0.0dB–+10.0dB
CRUSHER
Balance
OFF, 1–255
INST
[CTRL]
*4
SampleRate
0–255
Filter
0–255
*4 If you set the KIT: CTRL Sel parameter to InstFX, you can use
[CTRL]
the
knobs of the instrument edit section to control this.
(You can also set this in the screen that appears when you press
the
[CTRL SELECT]
button.)
Explanation
Specifies the output level.
Set this so that the volume is
approximately the same whether
MASTER FX Sw is on or off.
Specifies the frequency below which
the low-frequency region of the input
is cut.
As you raise the HpFreq value, the
region being cut extends into the
high-frequency region.
Specifies the center frequency of the
EQ that is applied before distorting
the sound.
Specifies the low-frequency level of
the EQ that is applied before distorting
the sound.
Specifies the high-frequency level of
the EQ that is applied before distorting
the sound.
By slightly decreasing the high-
frequency level, you can reduce
the higher-order partials that are
generated when the sound is
distorted.
Specifies the center frequency of the
EQ that is applied after distorting the
sound.
Specifies the low-frequency level of
the EQ that is applied after distorting
the sound.
Specifies the high-frequency level of
the EQ that is applied after distorting
the sound.
Adjusts the lo-fi effect.
With a setting of 255, the lo-fi effect is
at 100%.
Specifies the sampling frequency at
which CRUSHER resamples the sound.
Higher settings of SampleRate lower
the sampling frequency, producing a
more lo-fi sound.
Specifies the cutoff frequency of the
LFP that is applied before CRUSHER
resamples the sound.
By lowering the Filter value, you can
reduce harsh high-frequency noise.
33
Advertisement
Table of Contents
