Table of Contents
Advertisement
Parameter
Value
-INF, -53.0dB–
HP Level
0.0dB–+10.0dB
-INF, -53.0dB–
BP Level
0.0dB–+10.0dB
-INF, -53.0dB–
LP Level
0.0dB–+10.0dB
-INF, -53.0dB–
Bypass
0.0dB–+10.0dB
COMPRESSOR
Balance
OFF, 1–255
MASTER FX
[CTRL]
*1
Attack
0–255
MASTER FX
[CTRL]
*1
Release
0–255
MASTER FX
[CTRL]
*1
Thre
-40dB–0dB
-40dB–0dB–
Gain
+40dB
1: 1.00, 1: 1.12,
1: 1.25, 1: 1.40,
1: 1.60, 1: 1.80,
Ratio
1: 2.00, 1: 2.50,
1: 3.20, 1: 4.00,
1: 5.60, 1: 8.00,
1: 16.0, 1: INF
HARD, SOFT1,
SOFT2, SOFT3,
Knee
SOFT4, SOFT5,
SOFT6, SOFT7,
SOFT8, SOFT9
DRIVE
Balance
OFF, 1–255
MASTER FX
[CTRL]
*1
Drive
0–255
MASTER FX
[CTRL]
*1
Level
0–255
MASTER FX
[CTRL]
*1
Explanation
Specifies the HPF level of the filter.
Specifies the BPF level of the filter.
Specifies the LPF level of the filter.
Specifies the bypass level.
Adjusts the compression effect.
With a setting of 255, the compression
effect is at 100%.
Specifies the time from the moment
that the input exceeds the level
specified by Thre until the volume
starts being compressed.
As the Attack is increased (lengthening
the time), the beginning of the note
will no longer be compressed.
Specifies the time from the moment
that the input falls below the level
specified by Thre until compression
stops being applied.
As the Release is increased
(lengthening the time), the sound will
have more sustain.
Specifies the level at which
compression begins.
Set a lower value for Thre if you want
to apply compression deeply, or if the
input level is low.
Because setting a low value for Thre
also lowers the output level, raise Gain
to make adjustments.
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
Specifies the compression ratio.
The higher the ratio, the more
compression is applied to the sound
when its level exceeds the Thre
setting.
If the ratio is set to 1: INF, the sound
will not become any louder than the
level specified by Thre.
Adjusts the character of the
compression.
HARD compresses the sound
suddenly, producing a hard sound.
SOFT compresses the sound gently,
producing a soft sound.
Adjusts the drive effect.
With a setting of 255, the drive effect
is at 100%.
Adjusts the depth of distortion.
Because increasing the Drive setting
also increases the output level, make
adjustments by lowering the Level
setting.
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
Parameter
Value
HpFreq
0–255
MASTER FX
[CTRL]
*1
PreEqFreq
0–255
MASTER FX
[CTRL]
*1
PreEqL
-INF, -53.0dB–
MASTER FX
0.0dB–+10.0dB
[CTRL]
*1
PreEqH
-INF, -53.0dB–
MASTER FX
0.0dB–+10.0dB
[CTRL]
*1
PostEqFreq
0–255
MASTER FX
[CTRL]
*1
PostEqL
-INF, -53.0dB–
MASTER FX
0.0dB–+10.0dB
[CTRL]
*1
PostEqH
-INF, -53.0dB–
MASTER FX
0.0dB–+10.0dB
[CTRL]
*1
OVERDRIVE
Balance
OFF, 1–255
MASTER FX
[CTRL]
*1
Drive
0–255
MASTER FX
[CTRL]
*1
Tone
0–255
MASTER FX
[CTRL]
*1
Level
0–255
MASTER FX
[CTRL]
*1
DISTORTION
Balance
OFF, 1–255
MASTER FX
[CTRL]
*1
Drive
0–255
MASTER FX
[CTRL]
*1
Tone
0–255
MASTER FX
[CTRL]
*1
Level
0–255
MASTER FX
[CTRL]
*1
Editing a Kit's Settings (KIT Edit)
Explanation
Specifies the frequency below which
the low-frequency region of the input
is cut.
As the HpFreq is raised, the region
being cut will extend further into the
high-frequency region.
Specifies the center frequency of the
EQ that is applied before distorting
the sound.
Specifies the low-frequency level of
the EQ that is applied before distorting
the sound.
Specifies the high-frequency level of
the EQ that is applied before distorting
the sound.
By slightly decreasing the high-
frequency level, you can reduce
the higher-order partials that are
generated by distortion.
Specifies the center frequency of the
EQ that is applied after distorting the
sound.
Specifies the low-frequency level of
the EQ that is applied after distorting
the sound.
Specifies the high-frequency level of
the EQ that is applied after distorting
the sound.
Adjusts the overdrive effect.
With a setting of 255, the overdrive
effect is at 100%.
Adjusts the depth of distortion.
Because increasing Drive also
increases the output level, make
adjustments by lowering Level.
Adjusts the tone.
Raising the Tone emphasizes the high-
frequency region.
Lowering the Tone emphasizes the
low-frequency region.
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
Adjusts the distortion effect.
With a setting of 255, the distortion
effect is at 100%.
Adjusts the depth of distortion.
Because increasing Drive also
increases the output level, make
adjustments by lowering Level.
Adjusts the tone.
Raising the Tone emphasizes the high-
frequency region.
Lowering the Tone emphasizes the
low-frequency region.
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
25
Advertisement
Table of Contents
