Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Charnwood C-Four Insert
Summary of Contents for Charnwood C-Four Insert
- Page 1 ® Insert charnwood Operating & Installation Instructions...
-
Page 3: Table Of Contents
C O N T E N T S O P E R AT I N G I N S T R U C T I O N S Quick Guide General Fuel Multifuel Grate Controlling the Fire Lighting Refuelling Ash Clearance Reduced Burning Cleaning and Maintenance Servicing... -
Page 4: Quick Guide
QUICK GUIDE Your Charnwood at a glance ® Throat plate Improves efficiency of stove by slowing down flue gases Door Keep closed when stove is in use Door handle Pull up to open Riddler handle Pull handle in and out to riddle. -
Page 5: General
OPERATING INSTRUCTIONS ® GENERAL Take care to only burn good quality fuels in order to obtain the greatest efficiency and to maintain the life of the appliance. Before lighting the stove, check with the installer that the work and checks described in the Installation Instructions have been carried Wood out correctly and that the chimney has been swept, is sound and free Only dry well seasoned wood logs should be burnt on this appliance... -
Page 6: Multifuel Grate
OPERATING INSTRUCTIONS ® MULTIFUEL GRATE Your Charnwood stove is fitted with a multifuel grate which enables both solid fuels and wood to be burned effectively. The grate has two positions: 1) In the solid fuel position the grate bars are vertical with gaps in between allowing primary combustion air to come up through the grate and through the fuel bed. -
Page 7: Lighting
OPERATING INSTRUCTIONS ® LIGHTING On initial lighting, the stove may smoke and give off an odour as the silicon paint with which the firebox is painted reacts to the heat. This is normal and will cease after a short time, but meanwhile the room should be kept well ventilated. -
Page 8: Refuelling
Door Seals To make ash removal easier there is a special Charnwood ash carrier For the fire to operate correctly it is important that the door seals available. This may be purchased from your supplier or, in case of are in good condition. -
Page 9: Servicing
First remove the fuel retainer and the throat plate. Then sweep the modifications may only be carried out by the Manufacturer or their chimney ensuring that soot is removed from all horizontal surfaces approved agents. Use only genuine Charnwood replacement parts. after sweeping. THROAT PLATE AND FLUEWAY CLEANING... -
Page 10: Troubleshooting
If you need further help with your Charnwood then your Installer will be able to provide the answers to most questions. Your Local Charnwood Premier Dealer has a great deal of experience and will also be able to provide helpful advice. Further help is available from the Charnwood Customer... -
Page 11: Installation Instructions
This stove is not suitable combustion - see the section on Commisioning. for use in a shared flue system. External air kits are available, please contact Charnwood for more In addition to these instructions the requirements of BS 8303 and information (Ref TIS 120) BSEN 15287-1:2007 must be fulfilled. -
Page 12: Chimney
INSTALLATION INSTRUCTIONS ® Fig. 11 Limiting Dimensions of Surround and Opening Fig. 10 Minimum distances from combustibles 500mm 600mm The shaded grey area on the face of the surround is Dimension A: 280mm the minimum flat area required for inset installation. Dimension B: 251mm (Building regulations) Recommended:390mm (extension of door over hearth) Dimension A:... -
Page 13: Preparation Of Fireplace
INSTALLATION INSTRUCTIONS ® PREPARATION OF FIREPLACE A cover plate can be fitted to the rear outlet of the convection casing. The outlet on the rear of the air box is to be left open If the fireplace contains combustible materials, inlet and outlet air and no spigots are to be attached. -
Page 14: Fitting The Convection Casing, Flue Pipe And Stove
INSTALLATION INSTRUCTIONS ® 1. Attach flue collar to length of flexible flue liner FITTING THE CONVECTION CASING, FLUE PIPE AND STOVE Upper flue collar Having prepared the fireplace as described, the convection case, Collar can be positioned as necessary Flue liner depending on required angle of flue stove and flue pipe can now be fitted. - Page 15 INSTALLATION INSTRUCTIONS ® 4. SECURE THE CASING TO THE HEARTH Secure the stove by inserting screws through the holes in the base (see diagram). 5. MAKE GOOD THE OPENINGS AND FILL WITH INSULATION Make good the opening at the top and sides of the convection casing ensuring that a good seal is made with the side flanges.
- Page 16 INSTALLATION INSTRUCTIONS ® 8. SECURE THE FLUE ADAPTORS Flue pipe Working from the inside of the stove, push the flue collar up through the flue outlet to meet the upper flue collar, so that the coach bolts Convection casing come down through the holes. Secure bolts with nuts. Upper flue collar All flue connections must be well sealed.
-
Page 17: Pre-Lighting Check
The Charnwood C-Four Insert has recommended as suitable for within the stove before attempting to light a proper fire. Sometimes use in smoke control areas when burning wood logs. -
Page 18: Dimensions
C FOUR I DIMENSIONS (mm) ® ø77 FRONT VIEW BACK VIEW ø127 (for 5" flue) PLAN VIEW SIDE VIEW... -
Page 19: Parts Lists
# Please specify colour when ordering. shown. This drawing is for identification purposes only. charnwood BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM T : + 4 4 ( 0 ) 1 9 8 3 5 3 7 7 9 9 •... - Page 21 A.J WELLS & SONS LTD A.J WELLS & SONS LTD Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom A Division of A.J.Wells & Sons Limited Registered in England No. 03809371 EN13229:2001/A2:2004/AC:2007 C Four I ROOMHEATERS FIRED BY SOLID FUEL TR-CPD-2014 EC certificate of conformity Minimum distance to...
- Page 22 BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM T : + 4 4 ( 0 ) 1 9 8 3 5 3 7 7 7 7 •...