Moxa Technologies NPort W2150 Plus Quick Installation Manual

NPort W2150/2250 Plus Series
Quick Installation Guide
Third Edition, September 2009
1. Overview
The NPort W2150/2250 Plus wireless device servers are an ideal
choice for connecting serial devices such as PLCs, meters, and sensors
to an IP-based wireless LAN or Ethernet LAN.
Features
• Link any serial device to an IEEE 802.11a/b/g network.
• 1 and 2-port RS-232/422/485 models, up to 921.6 Kbps.
• Web-based configuration over Ethernet or wireless LAN.
• Enhanced security for remote configuration with HTTPS, SSH.
• Secure data access with WEP, WPA, WPA2.
• Built-in WLAN site survey tool.
• Wireless roaming when signal strength goes below user-defined
roaming threshold.
• Per-port offline port buffering and serial data log.
• Dual power inputs via power jack and terminal block.
2. Package Checklist
Before installing the NPort W2150/2250 Plus device server, verify that
the package contains the following items:
• 1 NPort W2150 Plus, NPort W2150 Plus-T, NPort W2250 Plus, or
NPort W2250 Plus-T.
• Document and Software CD.
• RJ45 to RJ45 cross-over Ethernet cable.
• Power adaptor (not including wide temperature models).
• Warranty Statement.
• Quick Installation Guide.
Optional Accessories
• DK-35A (35 mm DIN-Rail Mounting Kit).
• Power jack to terminal block power cable (P/N: 9199000000900).
Note: Notify your sales representative if any of the above items are
missing or damaged.
3. Hardware Introduction
The NPort W2150 Plus models have one serial port, and the NPort
W2250 Plus models have two serial ports. All models support
RS-232/422/485 operation with 8-pin RJ45 connectors, and include one
10/100M Ethernet port.
— 1 —
NPort W2150 Plus/W2150 Plus-T NPort W2250 Plus/W2250 Plus-T
100M LED (green)
Signal Strength LEDs
DB9 male connector
Reset Button—The reset button is used to load factory default settings.
Use a pointed object to hold the reset button down for 5 seconds to load
factory defaults.
End Panel LED Indicators
Name
Ethernet
P/N: 1802021501013
10M LED (orange)
Reset
button
Power jack
RJ45 10/100 Mbps
power input
Antenna
Ethernet port
Terminal Block
power input
DIN-Rail
screw hole
Wallmount screw hole
DB9 male connector
Color Function
Orange 10 Mbps Ethernet connection
Green 100 Mbps Ethernet connection
Off Ethernet cable is disconnected, or has a short
— 2 —
Top Panel LED Indicators
Name Color Function
Steady on: Power is on and NPort is booting up
Red
Blinking: IP conflict or DHCP/BOOTP server
did not respond properly
Ready
Steady on: NPort is functioning normally
Green
Blinking: NPort is responding to Locate
function
Off Power is off or a power error condition exists
Steady on: Wireless enabled
WLAN Green
Blinking: WLAN IP conflict or DHCP/BOOTP
server did not respond properly
Orange Serial port is receiving data
Serial 1
Green Serial port is transmitting data
Serial 2
No data is flowing to or from the serial port
Off
1 Red - the signal strength is between 0% ~ 20%
Red
2 Red - the signal strength is between 20% ~ 40%
Signal 3 Green - the signal strength is between 40%~60%
Strength
4 Green - the signal strength is between 60%~80%
Green
5 Green - the signal strength is between
80%~100%
4. Pull High/Low Resistors for RS-422/485
You may need to set the pull high/low resistors when termination
resistors are used for certain RS-422 or RS-485 environments.
NPort W2150 Plus/ NPort W2250 Plus/
NPort W2150 Plus-T NPort W2250 Plus-T
— 3 —