Subscribe to Our Youtube Channel
Related Manuals for HEATSTRIP INTENSE THY2200
Summary of Contents for HEATSTRIP INTENSE THY2200
- Page 1 Product Manual ® H E AT S T R I P I N T E N S E E l e c t r i c H e a t e r M o d e l T H Y 2 2 0 0...
-
Page 2: Product Overview
® as for workstation spot heating in factories, warehouses and showrooms. Within your home, HEATSTRIP can provide comfort heating for undercover alfresco dining and BBQ area, patios, verandas, courtyards and balconies. - Page 3 – similar to the heat rays emitted by the Sun. Radiant heating is the only viable option for outdoor or tough indoor sites. Maximum heat performance – multiple applications ® The high temperature output of the HEATSTRIP Intense is perfect for exposed outdoor sites, high ceilings and hard-to-heat indoor and outdoor applications.
- Page 4 Specifications - Australia LEAD POWER CURRENT DIMENSIONS WEIGHT MODEL LENGTH PLUG (WATTS) (AMPS) (mm) (Kg) (mm) THY2200 2200 1068 x 120 x 90 1000 MODEL HEATER TYPE High intensity electric radiant, infra-red overheat heater with carbon filament element. OUTPUT 2200 watts POWER 230-240 Volts Nominal at 50—60 Hertz, Single Phase CONNECTION...
- Page 5 ® The top diagram shows how HEATSTRIP Intense is recommended to be used directly over a table, while the bottom diagram indicates how to spot heat a large area.
-
Page 6: Selection Guide
Ideal mounting location: ceiling mounted, directly above area to be heated (eg. above a table) ® The below table outlines the coverage HEATSTRIP Intense model (in m ), based on 3 different scenarios. For example, in an outdoor area that is protected from prevailing winds by walls, café blinds etc, (eg outdoor enclosed) This data is based on direct overhead ceiling mounting. -
Page 7: Installation Requirements
For mounting heights more than 3m outdoors, we recommend the use of the optional accessories to reduce the height of ® the heater to 2.3m—2.5m. This will increase the effectiveness of your HEATSTRIP . Refer to the Mounting Accessory section for more information. -
Page 8: Installation Location
Installation location — the below diagrams confirm the minimum recommended clearances. Angled Wall Installation Surface Below Lights, fans, and sprinklers Heater must NOT be below heater Ceiling Installation Surface Below Lights, fans, and sprinklers Heater must NOT be below heater Angled Ceiling Installation... -
Page 9: Mounting Options
Mounting options ® The installation of HEATSTRIP Intense is simple and easy with the standard mounting brackets supplied. For other more challenging locations there are a range of mounting options available - refer to below diagrams. ® The HEATSTRIP Intense can be mounted directly to the ceiling, flush mounted into the ceiling, angled downwards on a wall, suspended on chains, poles or attached to beams and rafters. -
Page 10: Standard Mounting Brackets
Standard mounting brackets ® The HEATSTRIP Intense comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling or wall mount, and come with pre-set angle options of parallel, 22.5° and 45°. The flexible standard mounting bracket can be turned 90 degrees to mount onto a beam, it can also be used to suspend with chains. - Page 11 MOUNTING Fix the two mounting brackets to the ceiling or wall in the desired location (refer minimum bracket centre chart). Make sure the method of fixing (bolts or screws) will be more than strong enough to support the weight of the heater, allowing for strong winds and other conditions.
- Page 12 Extension Mount Bracket ® The Extension Mount bracket allows HEATSTRIP Intense units to be lowered from high ceilings using rigid connections. The standard length options as part of the kit are 300mm, 600mm, 900mm and 1200mm. The extension mount bracket utilises components from the standard bracket kit which is supplied with each heater.
-
Page 13: Flush Mount Enclosure
Flush mount enclosure ® The Flush Mount Enclosure is an ideal way to neatly install the HEATSTRIP into a ceiling. They are available for the ® HEATSTRIP Intense model, and are supplied as a one-piece unit suitable for mounting individual heaters. Flush mounting can be used with plaster or timber lined ceiling materials. - Page 14 The TT-MTR-PLUG has been designed to provide easy remote control timer functionality to wall socket powered Heatstrip heaters. The unit can however be used to remotely operate with timer functionality any device powered by a standard 10A Australian wall socket outlet.
-
Page 15: Maintenance
Safety ® ® HEATSTRIP Intense has an IP rating of X5. This means it is safe for water ingress from all directions. The HEATSTRIP can be safely hosed down. ® HEATSTRIP has undergone extensive testing both in laboratory conditions; in Thermofilm’s manufacturing facility in Melbourne and field trials in Australia and overseas. -
Page 16: Warranty Terms And Conditions
® Thermofilm warrants to the original owner that HEATSTRIP Intense products will be free from defects in materials and workmanship for a period of 24 months for residential applications (and 12 months for commercial applications) from the date of purchase in accordance with the following warranty terms and conditions.
Need help?
Do you have a question about the INTENSE THY2200 and is the answer not in the manual?
Questions and answers