Subscribe to Our Youtube Channel
Related Manuals for HEATSTRIP THH-A series
Summary of Contents for HEATSTRIP THH-A series
- Page 1 R A D I A N T O U T D O O R H E A T E R S Product Manual ® H E AT S T R I P C l a s s i c ( T H H - A ) T h e h e a t e r t h a t i s a d e s i g n f e a t u r e !
-
Page 2: Product Overview
Rev F MAY14 ® There are three (3) different series of products within the Heatstrip product category. Each has a different temperature output, making them ideal for different applications. Below is a list of some common applications, to assist with the selection of the most effective and efficient series. - Page 3 ® spot heating in factories, warehouses and showrooms. Within your home, HEATSTRIP can provide comfort heating for undercover alfresco dining and BBQ area, patios, verandas, courtyards and balconies.
- Page 4 2.7 m in a fully enclosed outdoor area (For higher ceiling heights, units can be lowered using optional bracket kits or refer to the Heatstrip Max range) MOUNTING OPTIONS Suitable for ceiling, wall, beam, fixed umbrella and recess mounting. Also available for extension mount using rigid fixing poles and chain mount bracket.
- Page 5 ® HEATSTRIP is supplied to many international markets, and therefore is available in a range of voltages and ® lead configurations, in order to meet local market approvals. HEATSTRIP is fully compliant to the following international standards. Europe CE, ROHS, IEC 60335-2-30:2002...
- Page 6 ® 180 hours x $0.36 = $64.80 yearly running cost for 1800W HEATSTRIP ® 180 hours x $0.48 = $86.40 yearly running cost for 2400W HEATSTRIP ® 180 hours x $0.64 cents = $115.20 yearly running cost for 3200W HEATSTRIP...
- Page 7 The top table shows a comparison between spot heating over a table, or heating an entire area. ® The bottom table shows the flexibility of using HEATSTRIP to provide a comfortable environment, even when the layout of the area is very unusual.
- Page 8 H E A T E R S Radiant footprint ® HEATSTRIP electric heaters produce radiant heat which heats objects rather than the air. Therefore, it is imperative that objects to be heated (ie. people), are within the direct radiant footprint of the heater.
-
Page 9: Selection Guide
O U T D O O R H E A T E R S Selection guide ® General recommendations for HEATSTRIP Classic: Ideal mounting height: 2.3m to 2.5m. Maximum is 2.7m in a fully protected/enclosed outdoor environment. • Ideal mounting location: ceiling mounted, directly above area to be heated (eg. above a table) •... - Page 10 ® Selections are based on HEATSTRIP Classic being mounted at 2.4m from the floor and an undercover fully enclosed outdoor area.
-
Page 11: Installation Requirements
For mounting heights more than 2.7m, we recommend the use of the optional accessories to reduce the height of the ®. heater to 2.3m—2.5 m. This will increase the effectiveness of your HEATSTRIP Refer to the Mounting Accessory section for more information. -
Page 12: Installation Location
R A D I A N T O U T D O O R H E A T E R S Installation location —the below diagrams confirm the minimum recommended clearances. LIGHT, FAN OR SPRINKLER MUST NOT BE BELOW THE HEATER CEILING Wall 1500 Min. -
Page 13: Mounting Options
H E A T E R S Mounting options ® The installation of HEATSTRIP Classic is simple and easy with the standard mounting brackets supplied. For other more challenging locations there are range of mounting options available - refer to below diagrams. -
Page 14: Standard Mounting Brackets
H E A T E R S Standard mounting brackets ® The HEATSTRIP Classic comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling or wall mount, and come with preset angle options of parallel, 22.5° and 45°. -
Page 15: Flush Mount Enclosure
O U T D O O R H E A T E R S Flush mount enclosure ® The Flush Mount Enclosure is an ideal way to neatly install the HEATSTRIP into a ceiling. They are available for ® all HEATSTRIP Classic models, and are supplied as a one-piece unit for mounting of heaters. - Page 16 O U T D O O R H E A T E R S Pole / beam mounting kit The optional Pole/Beam mounting bracket kit can ® be used to mount HEATSTRIP Classic onto wooden beams, rafters, poles, umbrellas struts BEAM or POLE etc.
- Page 17 H E A T E R S Twin mounting bracket The optional Twin Mount bracket allows for two (2) units of HEATSTRIP Classic to be mounted side-by-side, either in parallel or angled as per the diagram on the right. This is ideal for applications when a wider heat coverage is required, or when there is mounting restrictions/limitations (such as running between 2 rows of tables etc.)
- Page 18 R A D I A N T O U T D O O R H E A T E R S End to end mounting bracket The end to end bracket allows multiple units to be joined in a straight line for maximum heat performance and aesthetic appeal.
- Page 19 Suspension mount bracket ® The Suspension Mount bracket provides a cheap, easy and effective option for lowering the HEATSTRIP Classic from high ceilings. If the ceiling height is more than 2.7m is an enclosed outdoor environment, it is recommended to lower the heaters to an ideal mounting height of 2.3m—2.5m.
- Page 20 Extension Mount Bracket ® The Extension Mount bracket allows HEATSTRIP Classic units to be lowered from high ceilings, using rigid connections. The brackets are for use with 25mm x 25mm x 1mm tube (SHS), and can be supplied as brackets only for customising the length of the drop on site;...
- Page 21 6 x THH 1500A or 4 x THH 1800A 16 m2 umbrella area 8 x THH 1500A or 6 x THH 1800A This is a guide only. For more detailed information, please contact the um- brella manufacturer, your nearest HEATSTRIP retailer or Thermofilm.
- Page 22 TT-MTM wall controller This controller is a custom designed and manufactured controller for Heatstrip. It has been designed for ease of use and low running costs of your heater. It provides both temperature control (allowing the user to turn the heat output up or down depending on the ambient temperature and conditions) and a timer for automatic heater operation.
-
Page 23: Maintenance
Carrying out the cleaning process at least every three months will reduce the amount of build up and keep the Heatstrip in good condition. If the heater is in a corrosive environment eg. salt spray, we recommend that you clean your heater with a light spray of fresh water every week. - Page 24 Heater wiring schematic diagrams ® The HEATSTRIP heater is required to be fitted with an "ON/OFF" isolation switch and can also be controlled with the use of a timer type control. It is recommended to use the TT-MTM Wall Controller for maximum performance and control options.
- Page 25 R A D I A N T O U T D O O R H E A T E R S Heater wiring schematic diagrams with relays When more heating units need to be connected from the same switch, a relay is needed. It is recommended that you talk to your electrician for more detail.
-
Page 26: Warranty Terms And Conditions
® Thermofilm warrants to the original owner that HEATSTRIP Classic products will be free from defects in materials and workmanship for a period of 24 months for residential use from the date of purchase in accordance with the following warranty terms and conditions.
Need help?
Do you have a question about the THH-A series and is the answer not in the manual?
Questions and answers