Subscribe to Our Youtube Channel
Related Manuals for HEATSTRIP Nano THN2000
Summary of Contents for HEATSTRIP Nano THN2000
- Page 1 Nano Electric Heater Product Manual HEATSTRIP® Nano (THN) www.heatstrip.com.au Ph: 03 9562 3455 E: sales@thermofilm.com.au...
- Page 2 Corrosion protection Built from corrosion resistant alloy, it is suitable for use in most applications, including difficult corrosive environments such as coastal areas. For exposed or windy areas, we would recommend the HEATSTRIP Intense or Max ranges. Multi-Purpose Mounting Options ®...
- Page 3 Specifications - Australia LEAD POWER CURRENT DIMENSIONS WEIGHT MODEL LENGTH PLUG (WATTS) (AMPS) (mm) (Kg) (mm) THN2000 2000 900 x 130 x 89.5 2000 MODEL HEATER TYPE Electric radiant, infra-red overheat heater with carbon filament element. OUTPUT 800 / 1200 / 1600 / 2000 Watts POWER 230-240 Volts Nominal at 50—60 Hertz, Single Phase CONNECTION...
- Page 4 ® The top diagram shows how HEATSTRIP Nano is recommended to be used directly over a table, while the bottom diagram indicates how to spot heat a large area.
-
Page 5: Selection Guide
For example, in an outdoor area that is protected from prevailing winds by walls, café blinds etc, (eg outdoor enclosed) We do not recommend this model for use in exposed outdoor locations. Use HEATSTRIP Max or Intense range. This data is based on direct overhead ceiling mounting. If the heaters are wall mounted, the radiant footprint will be reduced. -
Page 6: Installation Requirements
For ceiling mounting heights more than 2.5m outdoors, we recommend the use of the chains or wires to reduce the height of the ® heater to 2.1m—2.3m. This will increase the effectiveness of your HEATSTRIP Electrical connections/GPO’s should not be located at the back of the heater. They should be located outside the physical footprint of the units to minimize heat build-up behind the units. -
Page 7: Installation Location
Installation location — the below diagrams confirm the minimum recommended clearances. Angled Wall Installation Surface Below Lights, fans, and sprinklers Heater must NOT be below heater 1000mm Ceiling Installation Surface Below Lights, fans, and sprinklers Heater must NOT be below heater Angled Ceiling Installation... - Page 8 Standard mounting brackets ® The HEATSTRIP Nano comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling or wall mount, and come with pre-set angle options of parallel, 22.5° and 45°. The flexible standard mounting bracket can be turned 90 degrees to mount onto a beam, it can also be used to suspend with chains.
- Page 9 MOUNTING Fix the two mounting brackets to the ceiling or wall in the desired location (refer minimum bracket centre chart). Make sure the method of fixing (bolts or screws) will be more than strong enough to support the weight of the heater, allowing for strong winds and other conditions.
- Page 10 3). Note: All HEATSTRIP Nano heaters and their remote controls have the same frequency, so it is possible to control several heaters with just one remote.
-
Page 11: Maintenance
Safety ® ® HEATSTRIP Nano has an IP rating of 55. This means it is safe for water ingress from all directions. The HEATSTRIP can be safely hosed down. ® HEATSTRIP has undergone extensive testing both in laboratory conditions; in Thermofilm’s facility in Melbourne and field trials in Australia and overseas. -
Page 12: Warranty Terms And Conditions
® Thermofilm warrants to the original owner that HEATSTRIP Nano products will be free from defects in materials and workmanship for a period of 18 months for residential applications (and 12 months for commercial applications) from the date of purchase in accordance with the following warranty terms and conditions.
Need help?
Do you have a question about the Nano THN2000 and is the answer not in the manual?
Questions and answers