Page 1
Information furnished by DAQ system is believed to be accurate and reliable. However, no responsibility is assumed by DAQ system for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or copyrights of DAQ system.
Board User manual 1 . cPCI-SBC02 Introduction It is the low cost Single Board Computer (SBC) which equipped a low power and low Heat Atom processor. Features Intel Atom Processor Z520PT(Z510PT, Z530P) Intel system controller hub US15WPT chipset ...
Page 4
Board User manual Serial I/O Two serial ports , one can be used as touch input Parallel Port Four USB A connector, Two with 10pin header Watch dog timer Status LEDS Indication for Ready and operation Power Input Single +9 to + 15V range power max current is 1.5A...
Board User manual 2 . cPCI-SBC02 Appearance Table 2.1 Each Function Description Name Description POWER S/W Main Power switch of EMB-CPU04 SO-DIMMDDAR2 256M ~ 2GB memory MEMORY Intel US15WPTSCH Intel Atom PIC Express Slot PIC Express slot Connector. COM1 (J17) PIN Connecter for Serial Communication 1.
Page 6
Board User manual 2. PIN : TX1 3. PIN : Touch screen 4. PIN : Touch screen 5. PIN : GND Speaker SPK connecter USB 1/2 USB connecter IDE 2.0mm 44 PIN Flash memory connecter Two USB 10pin Header (J10) 1.PIN , 2.PIN : +5 V...
Page 7
SW, VGA, Network, USB Rear Side Compact PCI interface - The cPCI-SBC02 board can use to personal PC with the external Power +5V. In front side of the cPCI-SBC02 has the Connector Out (VGA, Power S/W, Ethernet, 2xUSB, Power LED, Audio-Jack).
Board User manual 3 . cPCI-SBC02 Assembly (Memory, Hard Disk) 1. Memory(SODIMM – SDRAM) Connection - Memory Connection with J4 connector(256M ~ 2G) - CF card connector board (It is necessary to change the board if it connects 1.8” hard.)
Page 9
Board User manual - Hard Disk Connection (This picture is CF card connection.) Notice) It is necessary to change the board if it connects 1.8” hard. The picture shows differently above picture http://www.daqsystem.com...
Board User manual 4 .Peripheral Device Control through Compact PCI Interface (Back-Plane) Usage – Our Product cPCI-EK01 cPCI-SBC02 Switch Audio Ethernet 2xUSB The cPCI-SBC02 can control the other Compact PCI products as to connect Back- Plane like above picture. http://www.daqsystem.com...
Board User manual 5 . Expansion Port through Transition Board 2xUSB RS232 serial Expansion rear 2xPS2 interface The transition board can use through the Back-Plane. And It is possible to use the expansion ports with connect the cPCI-SBC02. (Special Purchase) http://www.daqsystem.com...
Board User manual 6 . Driver Installation 6.1 AUDIO Driver Installation - Execute the CDROM:\Driver\audio\audio_WDM_R241\setup.exe in CD-ROM. 6.2 LAN Driver Installation - Execute the CDROM:\Driver\Lan\AsusSetup.exe in CD-ROM. http://www.daqsystem.com...
Board User manual 6.3 Touch Driver Installation (When 7” LCD want to use.) - Execute the CDROM:\Driver\Touch\SetupVista32-RS232.exe in CD-ROM, display the icon of TouchWare at the wallpaper. - Double click the TouchWare. - Click the “HW Info”. - Click the “Auto Search Touch” button, check the connection port.
Page 14
Board User manual - When show the below display, press the lighting point. (You should continuously press until completed progress bar.) - Press “Yes”, and then finished the install. http://www.daqsystem.com...
Page 15
Board User manual 6.4 Graphic Driver Installation (When 7” LCD want to use.) - Execute the CDROM:\Driver\Graphic\XP\setup.exe in CD-ROM, install the Graphic driver and re-booting. Installation when including LCD Setup Display After click the right mouse at the display properties, and choose the “Graphic Property”.
Page 16
Board User manual MID Monitor AND DeskTop Monitor Single Output - MID Monitor and DeskTop Monitor (VGA Connecter) are all “Graphic Properties” setting screens in connection state. - It can be displayed to choose one of the two (MID Monitor or Desk Top Monitor) in case of “Single Display”...
Page 17
Board User manual MID Monitor AND Desk Top Monitor Multiple Output - When “Intel(R) Dual Display Clone” is set in “Multiple Display”, it is possible to display same display output at MID Monitor and DeskTop Monitor. (Same Display Output) - It can be use the expansion monitor to make a monitor between the MID Monitor and Desk Top Monitor, in case of setting “Expansion Desk Top”.
Board User manual Only DeskTop Monitor Installation when not including LCD When Installation Graphic Driver and re-booting, windows logo display shows at DeskTop Monitor as like below picture. After logo display disappear, do not show nothing at DeskTop Monitor because a graphic driver outputs a display at initial setup LCD.