Table of Contents
Advertisement
Troubleshooting
Cause
The sound from the device connected to an INPUT jack or OUTPUT jack is not
loud enough
Could you be using a cable that has a built-in re-
sistor?
No signal is sent from DIGITAL OUTPUT
Could the POWER SAVE switch (p. 4) be "ON"?
Power does not turn on (POWER indicator will not light)
Is the POWER switch set correctly?
Are the batteries installed correctly?
Is the AC adaptor connected correctly?
Could the batteries be exhausted?
Sound is distorted or crackly
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Is the volume adjusted appropriately?
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Too much noise in the sound
Have you minimized the volume of the channels
you're not using?
The sound from a mic connected to the plug-in power compatible INPUT jack is
heard only from the L side
Have you connected a stereo mic?
Hum (a buzzing noise) is heard
If you've connected two or more devices together,
the ground path may form a loop, picking up
noise that you will hear as hum.
Response
Use a cable that does not contain a built-in resis-
tor.
If the "Power Save" function is on, the digital au-
dio signal will not be sent from the DIGITAL
OUTPUT jack in order to reduce power consump-
tion.
Set this to "DC IN" if you're using the AC adap-
tor, or to "BATT" if you're using batteries.
Check the polarity of the batteries.
Make sure that the AC adaptor plug is inserted all
the way.
For Canada
Install fresh batteries.
NOTICE
Use the SENS knobs, channel volume knobs, and
AVIS
MAIN volume knob to adjust the volume appro-
priately (p. 9).
If you're not using a channel, turn its SENS knob
and channel volume knob to the minimum posi-
tion.
The plug-in power compatible INPUT jack is de-
signed for the use of stereo input.
It cannot be used with a monaural mic.
• Operate the mixer on batteries.
• If you're using monitors that have digital input
(e.g., MA-15D or the DS series), make
connections using optical cables.
11
Main Specifications
M-10MX: 10 channel (5 stereo) Mixer
Number of Channels
10 in 2 out
AD Conversion
Sample Rate: 44.1/48.0/96.0 kHz, Signal Processing: 24 bits
96.0 kHz: 20 Hz to 40 kHz (+1/-2 dB)
Frequency Response
48.0 kHz: 20 Hz to 22 kHz (+1/-2 dB)
44.1 kHz: 20 Hz to 20 kHz (+1/-2 dB)
Residual Noise Level
-86 dBu (IHF-A, typ.)
Input Jacks 1–6: -50 to +4 dBu
Input Jacks 1–2: -40 to +10 dBu
Nominal Input Level:
Input Jacks 5–10: -2 dBu
* Maximum input level: Nominal input level + 12 dB
-2 dBu
Nominal Output Level
* Maximum output level: +10 dBu
Input Jacks 1–6 (1/4 inch phone type, unbalanced)
Input Jacks 1–2 (Stereo miniature type, plug-in powered)
Input Jacks 5–10 (RCA pin type)
Main Output Jacks L, R (1/4 inch TRS phone type (impedance balanced),
Connectors
RCA pin type)
DC IN (AC adaptor) Jack
Digital Output Connectors (Optical type, Coaxial type)
Headphone Jack (Stereo miniature type)
Power Supply
DC 9 V (AC adaptor), Alkaline dry battery LR6 (AA) type x 4
250 mA
* Expected battery life under continuous use:
Current Draw
Alkaline: 6 hours (Power save mode: On), 4 hours (Power save mode: Off)
These figures will vary depending on the actual conditions of use.
181.2 (W) x 107.5 (D) x 54.0 (H) mm
Dimensions
7-3/16 (W) x 4-1/4 (D) x 2-1/8 (H) inches
Weight
393 g / 14 oz
Accessories
Owner's Manual, AC Adaptor, Ferrite Core
* 0 dBu = 0.775 V rms
In the interest of product improvement, the specifications and/or appearance of this unit are subject
to change without prior notice.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For Canada
NOTICE
AVIS
12
Advertisement
Table of Contents
