Roland SH-201 Owner's Manual page 69

Parameter Value
TRANSMIT SWITCH
PROGRAM OFF, ON
CHANGE
BANK SELECT OFF, ON
EDIT DATA OFF, ON
ACTIVE SENSING OFF, ON
KEYBOARD parameters
Parameter Value
OCTAVE SHIFT -3– +3
TRANSPOSE -5– +6
VALUE
LOCAL SWITCH OFF, ON
REMOTE OFF, ON
KEYBOARD
PEDAL parameters
Parameter Value
PEDAL POLARITY STANDARD,
REVERSE
PEDAL ASSIGN HOLD,
MODULATION,
VOLUME,
BALANCE,
PAN,
EXPRESSION,
START/STOP,
ARP-SW
Explanation
If this is "ON," a program change message will be trans-
mitted when you press a NUMBER button or BANK
button.
If this is "ON," a MIDI bank select message will be
transmitted when you press a GROUP button (PRESET
or USER).
If this is "ON," changes you make to the patch settings
will be transmitted as system exclusive messages.
Turns transmission/reception of active sensing mes-
sages on/off.
Explanation
Shifts the keyboard pitch up or down in steps of one oc-
tave.
Shifts the keyboard pitch up or down in semitone steps.
Determines whether the sound generator section is dis-
connected (OFF) from the controller section (keyboard,
pitch bend/modulation lever, knobs, buttons, D Beam
controller, pedal, and so on); or not disconnected (ON).
* Normally this is left "ON," but if you wish to use the
SH-201's keyboard and controllers to control only
external sound modules, set it to "OFF."
Set this parameter "ON" when you want to use an ex-
ternal MIDI keyboard instead of the SH-201's keyboard.
In this case, the MIDI transmit channel of the exter-
nal MIDI keyboard can be set to any channel.
* Normally you will leave this parameter "OFF."
Explanation
Selects the polarity of the pedal.
On some pedals, the electrical signal output by
the pedal when it is pressed or released is the
opposite of other pedals. If your pedal has an
effect opposite of what you expect, set this pa-
rameter to "REVERSE."
* If you are using a Roland pedal (that has no po-
larity switch), set this parameter to "STAN-
DARD."
Selects the function controlled by a pedal connect-
ed to the PEDAL jack.
HOLD: Sustain the sound while you continue
holding down the pedal (p. 21).
MODULATION: Apply modulation when you
press the pedal.
VOLUME: Control the volume.
BALANCE: Vary the volume balance between
the UPPER tone and LOWER tone.
PAN: Move the left/right position (when out-
putting in stereo).
EXPRESSION: Add expression to your perfor-
mance (p. 21).
START/STOP: Press the pedal to start/stop re-
cording or playback on the recorder.
ARP-SW: Press the pedal to turn the arpeggia-
tor on/off.
Parameter list
Panel operation
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK C button
3. Press a NUMBER button (5–8)
5: PROGRAM CHANGE
6: BANK SELECT
7: EDIT DATA
8: ACTIVE SENSING
Lit: ON, Dark: OFF
4. Press the CANCEL button
Panel operation
Press the OCT UP/DOWN buttons (p. 18)
Hold down the CANCEL button and press
the OCT UP/DOWN buttons
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK D button
3. Press the NUMBER 2 button
Lit: ON, Dark: OFF
4. Press the CANCEL button
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK D button
3. Press the NUMBER 3 button
Lit: ON, Dark: OFF
4. Press the CANCEL button
Panel operation
Hold down the CANCEL button and press
a GROUP button (PRESET or USER)
PRESET: STANDARD
USER: REVERSE
Hold down the CANCEL button and press
a NUMBER button (1–8)
1: HOLD
2: MODULATION
3: VOLUME
4: BALANCE
5: PAN
6: EXPRESSION
7: START/STOP
8: ARP-SW
69