Furuno GP-1871F Installation Manual page 24

APPENDIX 1 MENU TREE
1
Files Screenshots Screenshots (shows number of screenshots saved to internal memory)
Export to SD
User Data Export File Format (C-MAP, GPX, CSV)
Routes and
Points
Tracks
Settings
Export to SD
Backup
Restore from SD (select file to import)
Notifications Export to SD (CSV)
Log
Units Units Distance (NM, SM, km, NM+ft, NM+m, SM+ft)
Speed (kn, km/h, m/s, mph)
Wind Speed (kn, km/h, m/s, mph, Bft)
Depth (m, ft, fm, pb, HR)
Fish Size (cm, inch)
Temperature (°C, °F)
Air Pressure (hPa, mBar, mmHg, inchHg)
Oil/Boost Pressure (Bar, PSI, kPa)
Volume (l, US gal, UK gal)
Height/Length (m, ft)
Fuel Rate (l/h, US gal/h, UK gal/h)
Formats and Bearing Display (M, T)
References Magnetic Variation (Internal, External)
True Wind Calculation Reference (Ground, Surface)
Position Format (DD°MM.MMMM', DD°MM.MMM', DD°MM.MM',
Restore Restore Default Settings (Select Yes/No from pop up window)
Defaults
Initial Language (English US, English UK, others)
Setup
Vessel Vessel Type (Power Displacement, Power Planing, Sail Boat)
Autopilot NAVpilot Control (ON, OFF)
Navigation Position Filter (Off, Low, Medium, High)
Setup Speed Filter (Off, Low, Medium, High)
Map Datum (WGS 1984, others)
Perspective Angle (5° to 60°, 30°)
SBAS Mode (ON, OFF)
Internal
Restart GPS
GPS Setup
Dynamic Model (At Sea, Automotive)
Navigation Speed (Low, High)
Data
GP330B SBAS Mode (ON, OFF)
Acquisition
WB200 SBAS Mode (ON, OFF)
SC-30 Setup SBAS Mode (ON, OFF)
Heading Offset (-180.0° to +180.0°, 0°)
Pitch Offset (-90.0° to +90.0°, 0°)
Roll Offset (-90.0° to +90.0°, 0°)
Max RPM (4000, 8000, 12000, 16000, 20000)
Instruments
Max Oil Pressure (600 kPa, 800 kPa, 1000 kPa)
Range
Setup Max Engine Boost Pressure (160 kPa, 200 kPa, 320 kPa)
Max Engine Coolant Pressure (320 kPa, 520 kPa, 600 kPa)
Max Fuel Pressure (320 kPa, 520 kPa, 600 kPa)
Engine Temperature (86 to 302°F, 122 to 410°F)
Engine Oil Temperature (86 to 302°F, 122 to 410°F)
Transmission Temperature (86 to 302°F, 122 to 410°F)
2
AP-6
Routes/Points (Shows number of routes/points
saved to internal memory)
Export to SD
Import from SD (select file to import)
Tracks/Track Points (Shows number of routes and
points saved to internal memory)
Export to SD
Import from SD (select file to import)
DD°MM'SS.ss", DD.DDDDDD)
2
Engine Setup Engines (1, 2, 3, 4)
Manual Fuel Manual Management (ON, OFF)
Management Total Fuel Capacity (0 to 9999 US gal)
NMEA Output Instance (0, 1, 2, 3, 4, 5)
IF NMEA Select IF (Select [IF-NMEAFI] to set the analog data that is input
Setup from the IF-NMEAFI.)
Category (Wind,ST800/ST850, Fuel, Fresh Water, Waste
Water, Live Weel, Oil, Black Water)
Resistance Full (0 ohm to 300 ohm; default: 33.50 ohm)
Resistance Mid (0 ohm to 300 ohm; default: 310.00 ohm)
Resistance Empty (0 ohm to 300 ohm; default: 240.00 ohm)
Capacity (0 to 2650 US gal)
Self Test (Starts a diagnotic test)
Refresh (Refresh the NMEA device list)
Rudder PORT/STBD Reversing (ON, OFF)
Setup
About System Software Version
Information Build Number
Released
Boot Version
Kernel Version
RootFS Version
Cartography
Chart 1
Fish Finder Serial Number
Information
Program Version
Boot Version
FPGA Version
FPGA Program Version
C-Weather Information
About OSS
Copyright
Service (For technicians only, requires password)
Restore Restore Default Settings (Select Yes/No from pop up window)
Defaults
Restore All to Factory Defaults (Select Yes/No from pop up window)
Clear Clear All Data and Settings (Select Yes/No from pop up window)
Memory
AP-7
APPENDIX 1 MENU TREE