Table of Contents
Related Manuals for VarTech Systems VT29B-M
Summary of Contents for VarTech Systems VT29B-M
- Page 1 Solutions for Demanding Applications VarTech Systems Inc. Industrial CRT and Flat Panel Displays VT29B-M 29” Auto Sync Color Display User’s Guide Read these instructions completely before attempting to operate your new Color Display.
-
Page 2: Fcc Information
FCC Information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 3: Table Of Contents
Table of Contents Warning and Caution ................2 Important Safety Instruction ..............3-4 Connecting the Monitor ................5 PD Series Monitor Operation ..............6-7 Color Monitor Hand Held Remote Operation ........... 8 Power Management Function ..............9 Trouble Shooting ..................10 CRT Specifications .................11 Specifications....................12-13 Appendix: Timing Charts ................14... -
Page 4: Warning And Caution
Warning and Caution Warning 1. To prevent fire or shock hazard, do not expose this monitor to rain or moisture. 2. High voltage exists on the cathode-ray tube anode lead of this monitor. Before servicing, determine the presence of high voltage by connecting a H.V. -
Page 5: Important Safety Instruction
Important Safety Instructions Before operating this equipment, please ensure that you have carefully followed all the procedures outlined in the user’s manual. 1. Read all instructions 2. Save these instructions for later use 3. Follow all warnings and instructions marked on the product 4. - Page 6 Important Safety Instructions 11. If an extension cord is used with product, make sure the amperage rating of the extension cord matches the rating of the product. Also, make sure the total of all products plugged into the wall outlet does not exceed 15 amperes.
-
Page 7: Connecting The Monitor
Connecting the Monitor 1. Be sure the monitor and the system unit are switched off. 2. Connect the power cord into the AC INPUT of the monitor. 3. Connect the 15-pin connector of the signal cable to the video control- ler of the PC, or your signal source. -
Page 8: Pd Series Monitor Operation
MONITOR OPERATION User’s Controls Power Switch Push the Power Switch to turn the monitor on and off. The Power LED near the OSD adjustment switches will light when the power is on. The LED will display Green when a valid signal is present, Amber if the monitor is in power saving mode (sig- nal is interrupted from computer source). - Page 9 MONITOR OPERATION...
-
Page 10: Color Monitor Hand Held Remote Operation
Color Monitor Hand Held Remote Operation 1. Set “Address Setting” on dip switches at rear of monitor: Set Binary Code on both rows of switches SW 1 CONTROLS FIRST NUMBER, SW 2 CONTROLS SECOND NUMBER 1 = 1, 2 = 2, 3 = 4, 4 = 8; ADD VALUES TO ACHEIVE DESIRED NUMBER ON DIP ON = 1 ON DIP... -
Page 11: Power Management Function
Power Management Function The power management function, which is controlled through the computer, provides four distinct power states. The normal operating condition. The power LED will show Green. Standby The screen blanks after a pre-set amount of idle time. The power LED will appear Amber in this state Suspend Some electronic circuits go off after a pre-set amount of... -
Page 12: Trouble Shooting
Trouble Shooting The following chart describes some possible trouble shooting techniques. Please refer to this chart for trouble shooting before contacting a service dealer Problem Cause Remedy No Picture • Power cord • Connect power cord disconnected • Power switch is off •... -
Page 13: Crt Specifications
CRT SPECIFICATIONS MODEL VT29B-M VIEW SIZE 27” (68CM) DEFLECTION 110 DEG PHOSPHOR DOT PITCH 0.62 MM FACEPLATE FLAT... -
Page 14: Specifications
SPECIFICATIONS SCANNING FREQUENCIES Horizontal: 30-48 kHz Vertical: 50-120 Hz INPUT SIGNAL Video: RGB Analog, 0.7Vpp / 75 ohm Sync: Separate (H/V), Composite (H+V), Sync on Green (Sync on Green may require color reset to display white) Connectors: HD-15 Female D-Sub connector, 5 x BNC Monitor automatically selects input method. -
Page 15: Specifications
Remote Control Address selection switches Remote Control: Infrared remote control capable of adjusting individual selectable monitors via rear mounted DIP switches. WEIGHTS AND DIMENSIONS VT29B-M Net Weight: 117 Lbs (53 kg) Gross Weight: 125 Lbs (57 kg) Unit Dimensions: Width: 25”... -
Page 16: Appendix: Timing Charts
Appendix: Timing Charts... - Page 17 VARTECH SYSTEMS INC. HEADQUARTERS 11529 Sun Belt Ct. Baton Rouge, Louisiana 70809 Toll-Free: 800.223.8050 International Phone: 001.225.298.0300 Fax: 225.297.2440 E-mail: sales@vartechsystems.com 150-068 www.vartechsystems.com 3.07.05...