Table of Contents Getting to know the recorder ......................2 Using the Control panel ......................3 Inserting a memory card .........................4 Using your recorder in a vehicle ....................5 Operating basics ..........................7 Turning the recorder ON ......................7 Continuous recording ........................ 7 Event recording...........................8 Camera mode ..........................8 Playback mode ...........................8...
Getting to know the recorder Note: The screenshots and other presentations shown in this manual may differ from the screens and presentations generated by the actual product. Rear-view mirror Mini-USB port LCD monitor Camera lens Control panel Hooks Speaker Memory card slot Microphone...
Using the Control panel POWER - Press and hold for 2 seconds to manually turn the recorder on and off. - When the recorder is turned on, press to switch the LCD monitor on and off. REC/OK - In Recording mode, press to start and stop recording. - In Camera mode, press to take a 4-megapixel photo.
Inserting a memory card You must insert a memory card (not included) before you can start recording. The recorder supports memory cards with up to 32GB capacity. 1. Hold the card by the edges and gently insert it into the slot with the label facing the rear side of the recorder.
Using your recorder in a vehicle 1. Make sure that your car is parked on level ground. 2. Use the provided rubber bands to mount the recorder on the rear-view mirror securely. 3. a. Connect the car charger to the mini-USB port of the recorder and then plug it to the cigarette lighter.
Page 7
b. Install the GPS accessory (optional). Connect the GPS accessory to the mini-USB port of the recorder (i). Connect the car charger to the mini-USB port of the GPS receiver and then plug it to the cigarette lighter (ii). Use the provided double sided tape to place the GPS receiver in a proper location securely.
Operating basics Turning the recorder ON Complete the installation according to the instructions in the “Using your recorder in a vehicle” section. Once the vehicle engine is started the recorder automatically turns on. When the vehicle engine is turned off or the recorder's power is disconnected, the recorder automatically saves the recording and turns off.
Event recording By default if an event happens such as a sudden impact, high speed driving, an aggressive turn or an accidental crash the G sensor will prompt the recorder to start recording the event. If you want to manually start an event recording while continuous recording is in progress, press MENU.
Configuring the recorder While the recording is in progress, press REC/OK to stop recording. Then, press MENU to open the Settings menu. Press MENU repeatedly to cycle through the menu screens: Recording settings ( > System settings ( ) > GPS settings ( ...
3. Press REC/OK to complete calibration. G-Sensor Setting: Sets the sensitivity level (Off, High, Medium or Low) of the G sensor that allows automatical triggering of the event recording while continuous recording is in progress. System settings Language: Sets the language. ...
GPS settings Time Zone: Sets the time zone of your location and the system will automatically set the correct date and time accordingly. GPS: Enables or disables the GPS function of the device. GPS Location: Displays or hides the GPS information on the video. ...
Installing MiVue Manager Download MiVue Manager from the Support page of our website (www.mio.com/support) and follow the on-screen prompts to install it. Make sure to download the correct software version (Windows or Mac) according to your computer's operating system.
Page 14
Note: The Map screen may not display when the computer is not connected to the Internet or when your MiVue model does not support the GPS function. G sensor chart displays data in 3-axis waveform about the car’s shift forward/ backward (X), to the right/left (Y) and upward/downward (Z).
Page 15
: Mutes or unmutes the volume. : Adjusts the volume level. : Plays the video in full screen. Click to return to the normal view. : Displays the playback progress. You can click on a point along ...
For more information Caring for your device Taking good care of your device will ensure trouble-free operation and reduce the risk of damage. Keep your device away from excessive moisture and extreme temperatures. Avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of time.
Precautions and notices For your own safety do not operate the controls of the product while driving. Make sure that no object is blocking the camera lens and no reflective material is placed near the lens. Please keep the lens clean. ...
About the battery CAUTION! This unit contains a non-replaceable internal Lithium Ion battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns do not disassemble, crush, puncture or dispose of in fire or water. ...
Regulatory information (CE) For regulatory identification purposes, Mio™ MiVue™ R Series is assigned a model number of N460. Products with the CE marking comply with the Electromagnetic Compatibility Directive (2004/108/EC) - issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Standards:...
Page 20
Do not operate the device while driving. Using this product does not change the requirement for a driver to take full responsibility for his or her behavior. This responsibility includes observing all traffic rules and regulations in order to avoid accidents, personal injury or property damage. MiTAC Europe Ltd www.mio.com...