Download  Print this page

Arrow Revolution Quick Start Manual

Hide thumbs
   

Advertisement

Outside Assembly
1
(2) 8-32 x 3/4"
Flat Head
Combination Screws
3
2
(2) 8-32 x 3/4"
Flat Head
Combination Screws
Components
Directions
Quick Start Instructions
Before installation, disassemble the inside assembly, as shown above, by
Installation Instructions
removing the inside lever with the lever removal tool provided and separating
Door Marker
the support assembly from the inside escutcheon. Remove the battery cover
from the inside escutcheon by unscrewing the hex screw, using the Allen wrench
Outside Touchscreen Assembly
provided, and sliding the battery cover up and off (the hex screw does not come
Inside Support Assembly
completely out). The outside assembly remains assembled.
Inside Escutcheon Assembly:
Refer to complete installation instructions for more information if changing hands
• Inside Support Assembly
or adjusting door thickness is required.
• Inside Escutcheon
1. Install latchbolt in door. Attach with two screws provided.
• Inside Lever Handle
Note: Be sure that bevel edge of bolt faces strike.
• Battery Cover
2. Install strike on the door frame.
4 AA Alkaline Batteries
3. Insert outside assembly through door.
Latchbolt
a. Guide motor cable (red and black wires) through 2-1/8" diameter hole.
Strike
b. Guide touchscreen cable through 3/4" diameter upper hole.
Allen Wrench 3/32" (2.5 mm)
4. Guide motor cable through rectangular hole on inside support assembly.
Screw Pack (7 screws)
5. Slide inside support assembly over outside assembly, lining up top and
bottom screw guides with holes in door. Secure both assemblies with
2 Keys (If Cylinder Included)
(2) 10-32 x 2-1/2" flat head machine screws. Do not over-tighten.
For Technical Assistance call Arrow:
1-800-221-6529.
P/N 80-9150-0074-010 Rev A
An ASSA ABLOY Group brand
Quickstart Guide
Inside Assembly
Touchscreen
Cable
3b
5
3a
4
Support Assembly Screws
Motor Cable
(2) 10-32 x 2-1/2" Flat
1
Head Machine Screws
Escutcheon Screw
(1) 10-32 x 3/4" Pan Head
With Star Washer Screw
11
8
9
10
6. Attach motor cable connector to the inside escutcheon PC board header
marked "MOTOR."
7. Attach the touchscreen cable connector to the inside escutcheon PC board
header as illustrated.
8. Slide inside escutcheon over inside support assembly.
CAUTION:
a. Position motor cable against inside support assembly. Avoid pinching
wires against the steel shank of the assembly.
b. "Z" fold touchscreen wire cable and lay against the back recessed area
of the escutcheon assembly. Position and bend wires to prevent binding
when installing the escutcheon over the support assembly.
9. Install and secure the 10-32 x 3/4" pan head screw through the center of
the battery housing into the barrel nut of the outside assembly.
10. Slide on inside lever and push in to attach.
11. Insert four (4) AA alkaline batteries. The lock responds, "Welcome to the
Arrow Digital World."
12. Install battery cover and tighten hex head screw with Allen wrench
provided with lock.
HARDWARE INSTALLATION
Touchscreen
12
7
Cable
Reset Button
Connector
EXT-PWR / REMOTE /
MOTOR
MOTOR
EXT-PWR / REMOTE /
8b
6
Touchscreen Cable
Routing
"Z" Fold

Advertisement

Table of Contents
loading

  Related Manuals for Arrow Revolution

  Summary of Contents for Arrow Revolution

  • Page 1 Secure both assemblies with 2 Keys (If Cylinder Included) provided with lock. (2) 10-32 x 2-1/2" flat head machine screws. Do not over-tighten. For Technical Assistance call Arrow: 1-800-221-6529. P/N 80-9150-0074-010 Rev A An ASSA ABLOY Group brand...
  • Page 2 6. Enter a 4-12 digit PIN code for the User number followed by the key. Shut Down Time Press to add more users. 7. Press the key to complete the process and conclude the programming session. For Technical Assistance call Arrow: 1-800-221-6529. P/N 80-9150-0074-010 Rev A An ASSA ABLOY Group brand...