Advertisement
Quick Links
MA1705-EA
© 2017 CASIO COMPUTER CO., LTD.
Be sure to keep all user documentation handy for future reference.
Your watch may differ somewhat from the one shown in the illustration.
Stopwatch Second Hand
Click 2
Click 1
Crown
Stopwatch functions
To adjust the time setting
When the second hand is at
12 o'clock, pull the
Crown
Click 2.
Rotate the
Crown
to change the
time setting.
Push the
back in on a time
Crown
signal to resume timekeeping.
Note
Take care that you set the correct AM
or PM time.
When changing the time, move the
minute hand four or five minutes past
your final setting, and then back it up
to the setting you want.
Crown Operations
Some water-resistant models (100 meters, 200 meters) have a
screw-in crown. When you need to perform a crown operation,
rotate it away from you to unscrew it. Then pull the crown
out. Avoid applying undue force when pulling. The watch
loses its water resistance while the crown is unscrewed. After
performing a crown operation, fully screw the crown back in.
If your watch has a rotary bezel...
You can rotate the bezel to align its ▼ mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the ▼ mark.
Low Battery Alert
The second hand will jump at two-second intervals to alert you when the charge is low.
Have the battery replaced as soon as possible after low battery alert is indicated.
Stopwatch operation is disabled during low battery alert.
If low battery alert occurs during a stopwatch operation, the stopwatch will
automatically reset to all zeros and stop.
Operation Guide 5559
Minute Hand
Hour Hand
Day Indicator
30
Stopwatch Minute Hand
Second Hand
24 Hour Hand
To change the day indicator setting
Pull the
out to Click 1.
Crown
out to
Rotate the
away from you
Crown
to set the day.
Push the
Crown
back in.
Note
The day indicator setting uses a
31-day month. Make adjustments for
months of shorter lengths.
Avoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly
at midnight.
Crown
Loosen
Current
Using the Stopwatch
The stopwatch measures elapsed time in 1-second increments up to 9 minutes,
59 seconds.
Elapsed time
A
Start
Split time
A
Start
Two finishes
A
Start
Important!
Do not operate the stopwatch with the crown pulled out.
Note
An elapsed time operation will stop automatically at the end of 10 minutes.
Correcting the 0 Positions of the Hands
Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
Pull the
Crown
Use A (clockwise) and B (counterclockwise) to move the
Stopwatch Second Hand
Holding down either button will move the second hand at high speed, until you
release the button.
The
Stopwatch Minute Hand
After all of the hands are the way you want, push the
Important!
Timekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.
Specifications
Accuracy at normal temperature: ±20 seconds a month
Stopwatch: Measuring Capacity: 9'59" (10 minutes)
Measuring Unit: 1 second
Start
Measurements: Elapsed time; split time; two finishes
Other: Low battery alert
Battery: One silver oxide battery (Type: SR920SW)
Elapsed time
Battery Life: Approximately 3 years
Specifications are subject to change without notice.
A
A
A
Stop
Resume
Stop
B
B
A
Split
Split release
Stop
B
A
B
Split
Stop
Split release
Display time of
First runner
Second runner
second runner.
finishes.
finishes.
Display time of
first runner.
out to Click 2.
to 12 o'clock and the
Stopwatch Minute Hand
is syncronized with the
Stopwatch Second Hand
Crown
B
Reset
B
Reset
B
Reset
to 0.
.
back in.
1
Advertisement
