Advertisement
Adjusting the Beam Range
Adjust the beam range by shifting the lower lens up and down:.
Hold the cover in the UP position and slide the plastic tab in the
lower lens up or down on the side you wish to adjust, until the
module is aligned in the desired position. Align the top of the tab
with the required angle of the beam (Figure 2):
0° = 12m
5°= 10.5m
10° = 7.5m
15° = 5.25m
20° = 3m
Once adjusted, lock into place by pushing the tab into the slot.
Adjusting the Horizontal Beam
Beams (on either side of the module) are projected parallel to the
wall (default). The beams can be adjusted to project 3
from the wall, distancing the beam 60 cm / 24 in. from the wall in
order to avoid detection of unwanted objects next to the module
(Figure 2).
To adjust the beams in relation to the wall, identify the side
needing adjustment, and slide the lens tray in or out of the detector
to the required position:
0° - Slide the lens tray until it is flush with the top edge of the lens
holder.
3° - Slide the lens tray until it is flush with the bottom edge of the
lens holder.
Pull Out for 0°
(Parallel Beam to Wall)
Slide Up
or Down
for Range
Adjustment
Push in for 3°
(Beam 3° from Wall)
Figure 2 : Beam Adjustment
12m
40 ft
0
horizontally
12m
40 ft
Technical Specifications
Sensor
Lens
Processing
Startup Time
Detection Speed
Power Input
Current
Consumption
Coverage
PET Immunity
Anti- Mask
Alarm Indicator
Alarm Output
Anti-Tamper
Switch
Operating
Temperature
Humidity
Dimensions
RF Immunity
Standards
Warranty: For complete warranty information on this product please refer to the
Limited Warranty Statement found on the website: www.paradox.com/terms or
contact your local distributor. © 2016 Paradox Security Systems (Bahamas) Ltd. All
rights reserved. Specifications may change without prior notice.
Patents: One or more of the following US patents may apply: 7046142, 6215399,
6111256, 6104319, 5920259, 5886632, 5721542, 5287111, and RE39406 and other
pending patents may apply. Canadian and international patents may also apply.
Beam Range Adjustment
0°
20°
3m
f
0°
20°
3m
0
10 ft
Horizontal Beam Adjustment
0
4x dual low noise rectangular elements
2nd gen., flat, 2x dual beam, 1.7" focal point,
narrow beam long-range Fresnel lens
Digital APSP / Digital temperature
compensation
25 seconds
0.2m / sec. – 4m / sec. (0.6 ft / sec. – 13.1 ft /
sec.)
9 Vdc to 15 Vdc
Typical/Standby: 37mA, Max: 80mA
Bi-directional, independent, 2 x 3m to 12m
(10 ft. to 39 ft.) at 1.5m / 4.9 ft. height
Up to 40 kg (90 lb) - minimum 1.5m / 4.9 ft
installation height
Active IR detection for blocking 10 cm up to
30 cm and sprayed liquid
2x red LED for 3 seconds + buzzer
2x Solid State, N.C, 150 mA.
N.C. 28 Vdc, 0.15A
-35°C to +50°C / -31°F to +122°F
95% max.
L 8.2 in. x W 4.3 in. x D 2.7 in.
(21 cm x 11 cm x 7 cm)
Complies with EN 50130-4: 10V / m 80 MHz
to 2.7 GHz
EN 50131-2-2, Security Grade 2,
EN 50130-5 Environmental Class IVA
3m
12m
10 ft
40 ft
0°
60 cm
3°
12m
40 ft
NV780MX-EI00
01/2016
Advertisement
