Happymodel Snapper 6 FRSKY BNF User Manual

Notes:
1.The receiver signal will be unstable while the MSP(Connect to Betaflight) Connection established
2.The PID loop frequency must be 2kHZ at this firmware version, will update soon .
Specifications
Brand Name: Happymodel
Mode Name: Snapper6
Item Name: 1S Brushless Whoop racer drone BNF
Wheelbase: 65mm
Size: 81mm*81mm*36mm
Weight: 23g(without batter y)
Features
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
Powerful Brushless motor and Smooth ESC
CNC aluminum alloy propeller guard
Betaflight OSD support ,easy to get RSSI , Voltage and other info from your goggles
Frsky version support both EU LBT and NON-EU Frsky transmitter
Head lights ready
Camera angle adjustable
Components
Snapper 6 Frame
Crazybee F3 Flight controller Frsky
SE0603 KV19000 Motor 0.8mm shaft
31mm 3-blades propeller(4cw+4ccw)
AIO Camera & VTX
3.8v 250mah 30C/60C batter y
USB Lipo/LIHV Charger
1S06 6 way Lipo/LIHV charger
Propeller disassemble tool
Screwdriver
VTX Bands and Channels setup
Frequency switching:
By one button,Short press the button to change channel,1-8 adjustable.
Press and hold the button for 2s to change bands,1-6 adjustable.
Two groups of LEDs:
Group 1:6 BLUE LED stand for bands
Group 2:8 RED LED stand for channels
Blue LED1 and Red LED1 light on,indicating frequency
5865MHZ(BAND1 and CH1)
Blue LED1 and Red LED2 light on,indicating frequency
5845MHZ(BAND1 and CH2)
Blue LED6 and Red LED8 light on,indicating frequency
5600MHZ(BAND6 and CH8)
Blue LED 1
Video Out
Video In
GND
3.3-5.5V
Red LED 1
Frequency and channel frequency table:
Binding procedure
1. Power for the Snapper 6 and the LED Combo(2 red led and 2 white LED) will blinking slowly,
then Press and hold the bind button for 2 seconds, the LED Combo(2 red led and 2 white led)
will getting to be solid, this indicate the Snapper 6 Quadcopter is in binding mode
Basic Version Standard Version Part. NO.
SP601
1 1
SP602FR
1 1
SP603
4 4
SP604
1 1
SP605
1 1
SP606
1 3
SP607
1 0
SP608
0 1
SP609
1 1
SP610
1 1
Blue LED 6
Red LED 8
Snapper
6 Micro FPV Racing Drone FRSKY BNF Version
2. Turn on your Frsky Taranis transmitter, and move to BIND OPTION from SETUP MENU,
Choose receiver mode D16 or D8 according to your Betaflight receiver configuration
(Frsky_X = D16 mode, Frsky_D=D8 mode)
3.ENT [Bind] to binding with the Snapper 6, the LED Combo(2 red led and 2 white led) will
blinking slowly on the flight controller ,this indicate binding successfully, and then exist
binding mode of your Frsky transmitter, the LED Combo(2 red led and 2 white led) will getting
to be solid again, this indicate working normal.
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select FRSKY_X Provider for FRSKY D16 MODE or Select FRSKY_D Provider
for FRSKY D8 MODE, don't enable Serial RX since the CRAZYBEE Flight controller is integrated
SPI BUS Receiver
Arm/Disarm the Motor
1. The Default Arm/Disarm switch for Snapper 6
with Betaflight Configurator.
2.Turn on the Frsky transmitter (Use X9D+ as an example) and move to the MIXER interface,
Set "SA" or "SB" switch etc. for Ch5 to ARM/DISARM the motor.
3.The default channel map for Snapper 6 Frsky version is TAER1234, please make sure your
transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And
also you can found "Armed" displayed on your FPV Goggles or the FPV Monitor. Please make
sure keep the Snapper 6 level before arming .Be careful and enjoy your flight now !
Toggle the AUX1 Switch, the Green LED on Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid the Flight controller will getting to be solid
is AUX1(Channel 5),and you can also customize it