Advertisement
Note: The instructions and screenshots below are based the TZTL12F/TZTL15F.
Note: The instructions and screenshots below are based the TZTL12F/TZTL15F.
Home screen operation
Press the HOME/BRILL key to open the home screen. The home screen is
Press the HOME/BRILL key to open the home screen. The home screen is
where you access functions and menus, select displays and check sensor status.
where you access functions and menus, select displays and check sensor status.
Display selection
Rotate the rotary knob to put the orange
Rotate the rotary knob to put the orange
frame on the applicable display icon.
frame on the applicable display icon.
Menu operation
Lat
N 25°39.958'
Lon
N 80°09.352'
Range
13.00 NM
Bearing
New Point
Goto
New Route
Tide
Chart Info
Move Boat
Rotate the rotary knob to put the orange frame on the applicable menu item.
Rotate the rotary knob to put the orange frame on the applicable menu item.
Zoom in and out
Rotate the rotary knob to zoom in or out the chart scale (Plotter/Weather display) and select the range (Radar/Fish finder display).
Rotate the rotary knob to zoom in or out the chart scale (Plotter/Weather display) and select the range (Radar/Fish finder display).
Zoom in
Zoom in
Rotate the rotary knob in clockwise direction.
Rotate the rotary knob in clockwise direction.
Edge Swipe function (TZTL12F/TZTL15F only)
Press the EDGE key and operate the joystick to activate the Edge Swipe function: Quick page, Slide-out menu, [Layers]
Press the EDGE key and operate the joystick to activate the Edge Swipe function: Quick page, Slide-out menu, [Layers]
menu, and Data area.
menu, and Data area.
[Layers] menu
Data area
雨雪反射
Data
area
Radar Control
[Layers] menu
DATA
then
then
Cursor and Scroll modes
Press the CURS•SCRL key to switch the function of the joystick between the Cursor and Scroll modes.
Press the CURS•SCRL key to switch the function of the joystick between the Cursor and Scroll modes.
Cursor mode operation
In the cursor mode,
In the cursor mode,
the cursor appears on
the cursor appears on
the display other than
the display other than
the home screen and
the home screen and
menu. Operate the
menu. Operate the
joystick to move the
joystick to move the
cursor.
cursor.
Tips
Tips
• In the cursor mode, you can pan the display by moving the cursor to the edge of the screen. This function is available in the full screen
Plotter/Weather/Radar display.
• You can adjust the cursor speed on the [General] menu.
Switching displays and selecting an active window
Switching displays
When multiple displays are installed in the same network, press the
When multiple displays are installed in the same network, press the
CONTROL key to switch between displays that can be controlled
CONTROL key to switch between displays that can be controlled
with the MCU-004.
with the MCU-004.
Push the joystick to open the selected
Push the joystick to open the selected
display.
display.
256.4°R
Zoom out
Rotate the rotary knob in counterclockwise direction.
Rotate the rotary knob in counterclockwise direction.
Quick page
260
250
270
240
280
2:01 PM
230
290
Quick page
220
300
210
310
200
320
190
330
180
340
340
170
350
160
0
10
150
140
20
Data
area
130
30
120
40
6,695
110
50
60
100
90
70
ROUTE
RADAR
80
TX
then
then
Scroll mode operation
In the scroll mode, you
In the scroll mode, you
can pan the display
can pan the display
(Plotter/Weather/Radar
(Plotter/Weather/Radar
display), shift the range
display), shift the range
Cursor
and scroll back the
and scroll back the
picture (Fish finder
picture (Fish finder
display) with the
display) with the
joystick.
joystick.
Home screen
Push to Enter.
Push to Enter.
Push the joystick to
Push the joystick to
activate the selected item.
activate the selected item.
Zoom out
Slide-out menu
then
then
then
then
Selecting an active window
To select an active
To select an active
window in a split
window in a split
display, move the
display, move the
cursor on the
cursor on the
applicable window.
applicable window.
An orange frame
An orange frame
appears around
appears around
the current active
the current active
window.
window.
(Back of the mounting template)
Side-out
menu
How to inscribe/go to a point
How to inscribe a point
Push to Enter.
Move the cursor on the
Move the cursor on the
position to inscribe a point,
position to inscribe a point,
then push the joystick.
then push the joystick.
How to go to a point
Push to Enter.
Move the cursor on the
Move the cursor on the
point or position to set as
point or position to set as
a temporary destination,
a temporary destination,
then push the joystick.
then push the joystick.
How to inscribe an event mark
then
then
Open the Slide-out menu.
Open the Slide-out menu.
Select a mark.
Select a mark.
Cape Florida Light
fl1w 6s28m
Lat
N 25°39.958'
Lon
N 80°09.352'
Range
13.00 NM
Bearing
256.4°R
New Point
Push to Enter.
Goto
New Route
Tide
Select [New Point].
Select [New Point].
Cape Florida Light
fl1w 6s28m
Lat
N 25°39.958'
Lon
N 80°09.352'
Range
13.00 NM
Bearing
256.4°R
Goto
Push to Enter.
Move
New Route
Name
Select [Goto].
Select [Goto].
Push to Enter.
Select [Event].
Select [Event].
Push to Enter.
Push the joystick to
Push the joystick to
inscribe the selected
inscribe the selected
mark at the own ship
mark at the own ship
position.
position.
Advertisement
