Table of Contents
Advertisement
Appendix
Entering letters/characters
Standard
characters
Press the relevant key
the number of times
indicated.
Briefly press the hash
#
key
to switch from
"Abc" to "123" mode,
from "123" to "abc"
mode and from "abc"
to "Abc" mode.
Specifications
Batteries
Technology: Nickel-metal-hydride (NiMH); Size: AAA (Micro, HR03); Voltage: 1.2 V; Capacity: 400 - 1000 mAh
General specifications
DECT standard
GAP standard
Range
Base station power supply
Radio frequency range
Transmission power
Environmental conditions in operation
Base station power consumption
In standby mode
– Handset in base station
– Handset outside base station
During a call
Questions and answers
If you have any queries about the use of your telephone, visit our website at www.gigaset.com/service
for 24-hour support. The table below contains a list of common problems and possible solutions.
Problem
Nothing appears in
the display.
No wireless connec-
tion to the base sta-
tion, Base flashes in
the display.
You cannot hear a
ringer/dialling tone
from the fixed line
network.
Error tone sounds
after system PIN
prompt.
PIN forgotten.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x
1
1
£
$
¥
¤
2
a
b
c
2
ä
I
d
e
f
3
ë
4
g
h
i
4
ï
5
j
k
l
5
L
m n
o
6
ö
M
p
q
r
s
7
N
t
u
v
8
ü
O
w x
y
z
9
Q
1)
.
,
?
!
P
*
/
(
)
< =
#
# @
\
1) Space
Cause
The handset is not switched on.
The batteries are flat.
The handset is outside the range of the
base station.
The handset is not registered.
The base station is not turned on.
The phone cord supplied has not been
used or has been replaced by a new cord
with the wrong jack connections.
The system PIN you have entered is
incorrect.
13
á
à
â
ã
ç
é
è
ê
í
ì
î
ñ
ó
ò
ô
õ
ß
ú
ù
û
ÿ
ý æ ø
å
0
+
-
:
¿
¡
> %
&
§
is supported
is supported
up to 300 m outdoors, up to 50 m indoors
230 V ~/50 Hz
1880-1900 MHz
10 mW average power per channel, 250 mW pulse power
+5 °C to +45 °C, 20% to 75% relative humidity
A150/A250
A150A/A250A
ca. 1.0 W
ca. 1.2 W
ca. 0.8 W
ca. 1.0 W
ca. 1.0 W
ca. 1.2 W
Solution
Press the end call key
place the handset in the base station.
Charge or replace the batteries.
Move the handset closer to the base station.
Register the handset
Check the mains connector on the base station
¢
S. 4.
Please always use the phone cord supplied or ensure
that the pin connections are correct when purchas-
ing from a retailer: 3-4 assignment of telephone
leads/EURO CTR37.
Reset the system PIN to the default 0000
All handsets are de-registered. All settings are
reset. All lists are deleted.
"
'
;
_
a
for approx. 5 seconds or
¢
S. 10.
¢
S. 12.
Advertisement
Table of Contents
