Table of Contents
Advertisement
GAGGIA VELASCA
1.1 Entering Page
This page shows the firmware version installed, the supply voltage (230V
or 120V) and the AC net frequency (50Hz or 60 Hz)
It's always required to check if the firmware version shown on the display
is the same printed on the microcontroller label
Warning!
If the two version do not match the PCB must be dismissed
The CA goes to page 1 (KEYB)
1.2 Page 1 (KEYB)
Initial condition: no button pressed.
Whenever a button is pressed the "ON" word appears near the related
button number.
Pressing button N°1 the backlight color switches from WHITE to RED
Pressing button N°2 the backlight color switches from WHITE to PINK
Pressing button N°7 turns the STANDBY LED on.
To test button N°4 it must be pressed just one time because it causes the
CA to navigate to the next page
In case two or more buttons are pressed at the same time the display
shows the expression "TWO BTN!" This could be a useful warning if the
keyboard is not working properly
ERRORS occur if:
"ON" word does not appear or stays fixed on screen. In this case it's
necessary to check the communication flat cable connected between
the keyboard and the CPU-Power board. Should not, on the other hand,
change the display color, check the JP5 cable.
When accessing the Test Mode all the loads are turned off.
When accessing the Test Mode all the loads are turned off.
1.1 Entering Page
1.1 Entering Page
When accessing the Test Mode all the loads are turned off.
Verify the firmware version
1.1 Entering Page
This page shows the firmware version installed, the supply voltage
This page shows the firmware version installed, the supply voltage
(230V or 120V) and the AC net frequency (50Hz or 60 Hz)
(230V or 120V) and the AC net frequency (50Hz or 60 Hz)
This page shows the firmware version installed, the supply voltage
(230V or 120V) and the AC net frequency (50Hz or 60 Hz)
It's always required to check if the firmware version shown on
When accessing the Test Mode all the loads are turned off.
It's always required to check if the firmware version shown on
the display is the same printed on the microcontroller label
the display is the same printed on the microcontroller label
1.1 Entering Page
It's always required to check if the firmware version shown on
the display is the same printed on the microcontroller label
This page shows the firmware version installed, the supply voltage
(230V or 120V) and the AC net frequency (50Hz or 60 Hz)
Warning!
If the two version do not match the PCB must be dismissed
Warning!
Warning!
It's always required to check if the firmware version shown on
If the two version do not match the PCB must be dismissed
If the two version do not match the PCB must be dismissed
the display is the same printed on the microcontroller label
The CA goes to page 1 (KEYB)
Press STEAM (Press CAPPUCCINO for OTC version)
The CA goes to page 1 (KEYB)
The CA goes to page 1 (KEYB)
Warning!
If the two version do not match the PCB must be dismissed
1.2 Page 1 (KEYB)
1.2 Page 1 (KEYB)
1.2 Page 1 (KEYB)
The CA goes to page 1 (KEYB)
Initial condition: no button pressed.
Initial condition: no button pressed.
Initial condition: no button pressed.
Press all the buttons from N°1 till N°9
revNum
Whenever a button is pressed the "ON" word appears near the
Whenever a button is pressed the "ON" word appears near the
Whenever a button is pressed the "ON" word appears near the
related button number.
related button number.
related button number.
Pressing button N°1 the backlight color switches from WHITE to
Pressing button N°1 the backlight color switches from WHITE to
revNum
Pressing button N°1 the backlight color switches from WHITE to
RED
RED
RED
5.0
Pressing button N°2 the backlight color switches from WHITE to
Pressing button N°2 the backlight color switches from WHITE to
Pressing button N°2 the backlight color switches from WHITE to
revNum
PINK
PINK
PINK
Pressing button N°7 turns the STANDBY LED on.
Pressing button N°7 turns the STANDBY LED on.
Pressing button N°7 turns the STANDBY LED on.
To test button N°4 it must be pressed just one time because it
To test button N°4 it must be pressed just one time because it
To test button N°4 it must be pressed just one time because it
causes the CA to navigate to the next page
causes the CA to navigate to the next page
causes the CA to navigate to the next page
revNum
In case two or more buttons are pressed at the same time the
In case two or more buttons are pressed at the same time the
In case two or more buttons are pressed at the same time the
display shows the expression "TWO BTN!" This could be a useful
display shows the expression "TWO BTN!" This could be a useful
display shows the expression "TWO BTN!" This could be a useful
warning if the keyboard is not working properly
warning if the keyboard is not working properly
warning if the keyboard is not working properly
ERRORS occur if:
ERRORS occur if:
ERRORS occur if:
"ON" word does not appear or stays fixed on screen. In this case it's
"ON" word does not appear or stays fixed on screen. In this case it's
"ON" word does not appear or stays fixed on screen. In this case it's
necessary to check the communication flat cable connected
necessary to check the communication flat cable connected
necessary to check the communication flat cable connected
between the keyboard and the CPU-Power board. Should not, on
between the keyboard and the CPU-Power board. Should not, on
between the keyboard and the CPU-Power board. Should not, on
the other hand, change the display color, check the JP5 cable.
the other hand, change the display color, check the JP5 cable.
the other hand, change the display color, check the JP5 cable.
The CA switches to page 2 (INPUTS)
The CA switches to page 2 (INPUTS)
The CA switches to page 2 (INPUTS)
5.0
5.0
5.0
revNum
revNum
revNum
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Used to verify firmware version and some built-in parameters
Used to verify firmware version and some built-in parameters
Used to verify firmware version and some built-in parameters
Test Mode INTELIA EVO V2 AMF
Used to verify firmware version and some built-in parameters
Press STEAM
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
5.0
G Divella
Press all the buttons from N°1 till N°9
Press all the buttons from N°1 till N°9
Press all the buttons from N°1 till N°9
Author
Verified
5.0
G Divella
Author
Verified
G Divella
Author
Verified
5.0
G Divella
Author
Verified
Pressing STEAM button
Pressing STEAM button
Pressing STEAM button
G Divella
G Divella
G Divella
Author
Verified
Author
Verified
Author
Verified
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
05 SERVICE MODE
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Press STEAM
Press STEAM
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Press STEAM
12/06/2015
Approved
SaveDate
12/06/2015
Approved
SaveDate
12/06/2015
Approved
SaveDate
12/06/2015
Approved
SaveDate
12/06/2015
12/06/2015
12/06/2015
Approved
SaveDate
Approved
SaveDate
Approved
SaveDate
Filename
Filename
Filename
Filename
Filename
Filename
Filename
3/12
P/PP
3/12
P/PP
3/12
P/PP
3/12
P/PP
2/8
4/12
4/12
4/12
P/PP
P/PP
P/PP
- Quick Links:
- Disassembly
Hide quick links:
Advertisement
Table of Contents
