Warning Icons; Troubleshooting - Saeco GAGGIA VELASCA CMF-OTC Service Manual

can exit by pressing the standby button. If this occurs, empty and rinse
-
carefully the water tank, then ll it up to the CALC CLEAN level. Follow the
instructions in chapter 'First installation', section 'Manual rinsing cycle'
before brewing any beverage. If the cycle was not completed, the machine
-
will require another descaling cycle to be performed at your earliest
GAGGIA VELASCA
convenience.

3.3. Warning icons

Warning icons and error codes
Warning signals are displayed in red. Below you nd a list of the
Warning signals are displayed in red. Below you find a list of the warnings that may appear on the -
warnings that may appear on the display and their meaning.
display and their meaning.
-
-
Fill the water tank with fresh
water to the MAX level indication.
-
-
The brew group is not in the
-
machine. Insert the group.
-
Remove the coffee grounds
-
container and empty it.
-
-
- There is too much powder in the brew group. Clean the brew group.
- If an error code is triggered, check the section 'Meaning of error codes' to see what
-
the code on the display means and what you can do. The machine cannot be used
-
when this icon is on the display.
-
You forgot to place the lid on the pre-ground coffee compartment. If you do not
-
place it back within 30 seconds the display will return to the main menu and the
brewing cycle will be stopped.
-

3.4. Troubleshooting

Meaning of error codes
-
-
Error code Problem
Problem
Meaning of error codes
Problem
Error code Problem
The machine does
not switch on
-
The machine is in
DEMO mode.
Meaning of error codes
Error code Problem
The drip tray is
quickly filled.
The brew group is not in the machine. Insert the group.
-
Close the service door.
The brew group is not in the machine. Insert the group.
Close the service door.
Fill the water tank with fresh water to the MAX level indication.
-
Remove the co ee grounds container and empty it.
Close the service door.
The brew group is not in the machine. Insert the group.
Remove the co ee grounds container and empty it.
The bean hopper is empty. Put new co ee beans in the bean hopper.
Remove the co ee grounds container and empty it.
-
There is too much powder in the brew group. Clean the brew group.
-
Close the service door. If an error code is triggered, check the section 'Meaning of error codes' to
see what the code on the display means and what you can do. The
There is too much powder in the brew group. Clean the brew group.
machine cannot be used when this icon is on the display.
If an error code is triggered, check the section 'Meaning of error codes' to
see what the code on the display means and what you can do. The
machine cannot be used when this icon is on the display.
There is too much powder in the brew group. Clean the brew group.
If an error code is triggered, check the section 'Meaning of error codes' to
see what the code on the display means and what you can do. The
machine cannot be used when this icon is on the display.
Remove the co ee grounds container and empty it.
-
You forgot to place the lid on the pre-ground co ee compartment. If you
You forgot to place the lid on the pre-ground co ee compartment. If you
do not place it back within 30 seconds the display will return to the main
do not place it back within 30 seconds the display will return to the main
menu and the brewing cycle will be stopped.
menu and the brewing cycle will be stopped.
You forgot to place the lid on the pre-ground co ee compartment. If you
do not place it back within 30 seconds the display will return to the main
menu and the brewing cycle will be stopped.
There is too much powder in the brew group. Clean the brew group.
If an error code is triggered, check the section 'Meaning of error codes' to
Cause
see what the code on the display means and what you can do. The
machine cannot be used when this icon is on the display.
The machine is disconnected or
Cause
the main switch is in the OFF
position.
You forgot to place the lid on the pre-ground co ee compartment. If you
do not place it back within 30 seconds the display will return to the main
menu and the brewing cycle will be stopped.
The standby button has been
pressed for more than 8 seconds.
This is normal. The machine uses
Cause
water to rinse the internal circuit
and brew group. Some water
flows through the internal system
directly into the drip tray.
Possible solution
Cause
Cause
Possible solution
Meaning of error codes
Error code
Possible solution
Warning signals are displayed in red. Below you nd a list of the
warnings that may appear on the display and their meaning.
English
21
-
Fill the water tank with fresh water to the MAX level indication.
03 BRIEF INSTRUCTIONS
-
The brew group is not in the machine. Insert the group.
-
The bean hopper is empty. Put new co ee beans in the bean hop
The bean hopper is empty. Put
new coffee beans in the bean
English
21
hopper.
-
Close the service door.
Close the service door.
-
Remove the co ee grounds container and empty it.
-
There is too much powder in the brew group. Clean the brew gro
-
If an error code is triggered, check the section 'Meaning of error c
see what the code on the display means and what you can do. Th
machine cannot be used when this icon is on the display.
-
You forgot to place the lid on the pre-ground co ee compartmen
do not place it back within 30 seconds the display will return to th
Solution
menu and the brewing cycle will be stopped.
Possible solution
Check if the mains cord is inserted
correctly
Problem
Make sure the main switch is set in
ON position. (AMF-CMF)
Switch the machine off and then on
again using the main switch on the
back of the machine.
Empty the drip tray when the 'drip
tray full' full indicator pops up through
the drip tray cover.
Place a cup under the dispensing
spout to collect rinsing water.
Cause Possible
2/6