Advertisement
PDS Series
Quick Start Guide
Visibly yours
Analog Inputs
Connect to analog sources such
Connect to DVI or analog sources.
The connector's analog pins can be
as PCs, VTRs, and cameras.
Use breakout cables as required.
accessed with a breakout cable, or a
See * below for details.
(Inputs 7 and 8 not on PDS-701)
Input 3
Input 4
Input 1
Input 2
Status Menu
Program Input Type
P R O G R A M :
R G B
1 0 2 4 x 7 6 8 @ 5 9 . 9 4
Program Input Format
N E X T :
S D I
Next Input Type
N T S C ( 4 8 0 i )
Next Input Format
Sample Status Menu
• Input Type — Specifies the type of input signal
currently on Program.
• Input Format — Indicates video format on
Program. If the input is not valid, "Invalid Signal"
is shown.
• Next Input Type — Indicates next Program input
type, plus HDCP status (if applicable).
• Next Input Format — Indicates next Program
input format.
For HDCP sources, ensure the Output
Display device is HDCP-compliant.
IMPORTANT
Otherwise, the display device will be
blacked when protected content is
selected to be shown on that output.
• To display the Setup Menu from the
Status Menu, press SEL.
• To return to the Status Menu from
NOTE
any point in the Setup Menu, press
ESC repeatedly.
DVI-I Inputs
HD/SD SDI Input
Connect to 3G/HD/SD-
SDI source.
DVI to HD-15 adapter.
VIDEO INPUTS
Input 7
Input 8
Input 5
Input 6
Menu Tree
— only top level functions are shown
Status Menu
Setup Menu
Input
Input Format
Adjust On
Type
Colorspace
Auto Acquire
Aspect Ratio
Sizing Adjust
Timing Adjust
Contrast
Brightness
Color Balance
Processing
Save Config
Reset Config
Recall Config
Delete Config
* Breakout Cables for Analog Inputs
Use this table to
connect various source
formats to the PDS,
using the system's
analog input connectors
(Inputs 1 - 8).
Program Outputs
1 x DVI, 1 x Analog provided.
Both have the same
resolution, and both can be
used simultaneously.
Preview
SDI
PROGRAM
Output
Logo
Main
Selection
Preview *
Status
Save Pgm to Logo
*
Only in PDS-902
Delete Logo
Breakout Cable
Comp
S-Video
Wire Color
Video
(Y/C)
(YPbPr)
(Pr)
R
(Lum)
(Lum)
G
(Chrom)
(Pb)
B
H Sync
V Sync
Barco, Inc.
Toll Free:
Technical Support:
Preview Outputs
Communications
Connect to DVI or
Ethernet and Serial connectors are provided
analog preview
for communications with PDS. Use the
monitor.
Ethernet Menu and Serial Setup Menu to
set parameters. Use Ethernet connector to
(Only on PDS-902)
SERIAL
ETHERNET
System
User Preference
Trans Time
VFD Brightness
Ethernet
Auto Acquire
Auto Input Cfg
Serial Setup
Auto Input Save
Input EDID
Background
DVI Cable Equal
HDCP
Executive Mode
Auto Take
File Association
Black Auto Take
Temperature
Diagnostics
Menu Context
Save System State
YUV
RGB
RGB
RGB
Sync on Green
Comp Sync
Separate H V
+1 (888) 414-7226
Fax:
+1 (916) 859-2515
+1 (866) 374-7878
Website:
www.barco.com
run web-based GUI.
AC
Connect to
AC power
source.
Tech Support
Version
Phone
Web Address
Factory Reset
Reset All, Save EDID
Reset All
Firmware Upgrade
USB Upgrade
Web Upgrade
For complete details on
all installation, setup,
and operating
procedures, refer to the
PDS User's Guide.
P/N 26-1204004-00 Rev 01
Advertisement
