Uniden constantly works on improving our products . This includes updating our documentation PRO12800N0-4K HARD DISK DRIVE INSTALLATION . . . . . . . . . . . . . . .12 with the latest firmware changes.
Create a Preview Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Because Uniden strives to provide the latest technology and quality in all of its products, firmware updates may be available with no prior notice .
• In order to ensure normal heat dissipation, install the device in a well-ventilated area . • Use Uniden's recommended specific surveillance hard disk drives (Western Digital Purple or Seagate SkyHawk surveillance hard drives) when adding a hard disk drive .
NETWORK CONNECTION SCHEMATIC DIAGRAM Although it is not required, at this point in the installation you may run cables and 2 . Click Save . install the cameras . DISABLE DISK MISSING ALARM Disable this alarm for any HDDs that are not present . 1 .
INITIAL TURN UP _______ From Channel Setting/Channel Grouping/Tour (right column), set up Tour Groups if desired (see page 31) . _______ Check and adjust camera images for focus and field of view in Preview (see page RECOMMENDED TURN UP ORDER 33) .
DHCP and write down the IP address, mask, and gateway that the DHCP server/router assigns as shown in figure 5.5. Click Next. • Uniden ProSeries: QR codes display to download the Uniden ProSeries a . Apple QR code 1 . Select the Device Time top tab and manuallty set the device clock .
Basic Schedule Setup 1 . Select Channel Setting/Planning/Recording Setting . The default recording schedule displays all channels recording all the time . 2 . Select Setting . The Arming Schedule popup screen displays . 2 . Click Add User on the bottom right side of the screen . The Add User screen displays . 3 .
2 . Complete the fields. Click Save if your are finished. Click Copy To to copy the setting to other 2 . Select Save, then click Exit to return to the Recording Setting screen . channels . The Copy To screen displays . 3 .
1 . Go to Maintenance/System Information/Device Information top tab. The current firmware version and description display . 2 . Go to support.uniden.com and check if your system has the latest firmware version. 3 . Complete the fields. Click Save when your are finished. A confirmation screen displays. Click 3 .
5 . Click on the Enable RAID check box and click SAVE in the bottom right corner . This will Uniden ProSeries recorders come with high-quality hard drives designed for digital surveillance enable the RAID and erase all data on the drives . The drives will have to be formatted after systems with continuous 24/7 recording: configuration.
(estimated value) changes depending on the HDD array number, size, and configuration. 7 . If a WiFi access point is connected to the LAN, connect the Uniden ProSeries Mobile app (or 7 . Click Confirm to build the selected Array . Progress will be shown, and a pop-up window should via a web browser) to remotely access the recorder and cameras .
Confirm . • If you are not using a Uniden IPC, select the Onvif protocol . • If the IPC does not show up, check the IP address and the network, and try again .
SET UP PTZ CAMERA(S) Configure PTZ Camera From System Setting/PTZ Setting, set the following parameters: • Channel • Protocol • Decoder Address • Baud Rate • Data Bit • Stop Bit • Parity 3 . Using the popup keyboard, enter the new tour group's name and select the Return icon ( •...
Set Camera Settings for each Channel Set Up PTZ Cruise From Channel Setting/Channel Parameters, you can set camera/channel characteristics . Each of PTZ cruises use presets to create a cycle of camera images from preset positions . the tabs has a Channel field where you can select which channel's characteristics you are working with .
Page 19
• Stream Type • Video Type • Resolution • Bitrate Type • Bitrate • Frame Rate • Encoding Type • I Frame Interval You MUST select Save and Exit to save any changes made. Motion Tab This tab lets you define areas that WILL be triggered if motion is detected. When you open this tab, a red grid covers the screen (Default = Full Screen) .
Page 20
Snapshot Parameters Set up a camera to take a snapshot at specific intervals and resolutions through Channel Setting/ Smart Detection Channel Parameter/Snapshot Parameters tab .Parameters are: When you select Channel Setting/Smart Detection, logarithms activate based on the tab settings . •...