Siemens RUGGEDCOM RS900 Installation Manual
Hide thumbs
Also See for RUGGEDCOM RS900:
- Installation manual (32 pages) ,
- Installation manual (46 pages) ,
- Installation manual (46 pages)
Related Manuals for Siemens RUGGEDCOM RS900
Summary of Contents for Siemens RUGGEDCOM RS900
- Page 1 Preface Introduction Installing the Device RUGGEDCOM RS900 Communication Ports Technical Specifications Dimension Drawings Installation Guide Certification 10/2016 RC1024-EN-03...
-
Page 2: Security Information
Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. - Page 3 RUGGEDCOM RS900 Installation Guide Contacting Siemens Address Telephone E-mail Siemens Canada Ltd Toll-free: 1 888 264 0006 ruggedcom.info.i-ia@siemens.com Industry Sector Tel: +1 905 856 5288 300 Applewood Crescent Fax: +1 905 856 1995 Concord, Ontario www.siemens.com/ruggedcom Canada, L4K 5C7...
- Page 4 RUGGEDCOM RS900 Installation Guide...
-
Page 5: Table Of Contents
RUGGEDCOM RS900 Installation Guide Table of Contents Table of Contents Preface ......................Alerts ..............................vii Related Documents ..........................vii Accessing Documentation ........................viii Training ............................viii Customer Support ..........................viii Chapter 1 Introduction ..................... 1.1 Feature Highlights ........................1 1.2 Description ........................... 2 Chapter 2 Installing the Device .................. - Page 6 RUGGEDCOM RS900 Table of Contents Installation Guide 4.4 Fiber Optic Ethernet Port Specifications ..................20 4.5 Operating Environment ....................... 21 4.6 Mechanical Specifications ......................22 Chapter 5 Dimension Drawings ..................Chapter 6 Certification ....................6.1 Approvals ........................... 25 6.1.1 CSA ..........................25 6.1.2 ...
-
Page 7: Preface
Installation Guide Preface Preface This guide describes the RUGGEDCOM RS900. It describes the major features of the device, installation, commissioning and important technical specifications. It is intended for use by network technical support personnel who are responsible for the installation, commissioning and maintenance of the device. -
Page 8: Accessing Documentation
Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request... -
Page 9: Introduction
RUGGEDCOM RS900 to be placed in almost any location. The RUGGEDCOM RS900 can be mounted on a DIN rail or panel for efficient use of cabinet space. The integrated power supply supports a wide range of voltages (88-300 VDC or 85-264 VAC) for worldwide operability, as well as dual-redundant, reversible polarity, 24 VDC and 48 VDC power supply inputs for high availability applications requiring dual or backup power inputs. -
Page 10: Description
• CSA/UL 60950-1 safety approved to 85 °C (185 °F) Section 1.2 Description The RUGGEDCOM RS900 features various ports, controls and indicator LEDs on the front panel for connecting, configuring and troubleshooting the device. Figure 1: RUGGEDCOM RS900 1. POWER LED 2. ALARM LED 3. RESET Button 4. [Optional] Copper (10/100Base-TX) or Fiber Optic (100Base-FX) Ethernet Ports ... - Page 11 Shuts down and restarts the device. Communication Ports Receive and transmit data, as well as provide access to the RUGGEDCOM ROS Web interface. For more information about the various ports available for the RUGGEDCOM RS900, refer to Chapter 3, Communication Ports Failsafe Alarm Relay Latches to default state when a power disruption or other alarm condition occurs.
- Page 12 RUGGEDCOM RS900 Chapter 1 Installation Guide Introduction Description...
-
Page 13: Installing The Device
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens Canada Ltd could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. -
Page 14: Required Tools And Materials
Installing the Device in Hazardous Locations The RUGGEDCOM RS900 is designed to comply with the safety standards for Class I, Division 2, Zone 2 hazardous locations where concentrations of flammable gases, vapors or liquids may be present, as opposed to normal operating environments. -
Page 15: Mounting The Device
Section 2.3 Mounting the Device The RUGGEDCOM RS900 is designed for maximum mounting and display flexibility. It can be equipped with adapters that allow it to be installed on a 35 mm (1.4 in) DIN rail or affixed to a panel. -
Page 16: Mounting The Device To A Panel
Mounting the Device to a Panel For panel installations, the RUGGEDCOM RS900 can be equipped with panel adapters pre-installed on the top and bottom of the chassis. The adapters allow the device to be attached to a panel using screws. -
Page 17: Connecting Power
Secure the adapters to the panel with #6-32 screws. Section 2.4 Connecting Power The RUGGEDCOM RS900 supports power input from a single high AC/DC or low DC power supply. IMPORTANT! • For 110/230 VAC rated equipment, an appropriately rated AC circuit breaker must be installed. -
Page 18: Connecting High Ac/Dc Power
Chapter 2 RUGGEDCOM RS900 Installing the Device Installation Guide • Section 2.4.2, “Connecting Low DC Power” Section 2.4.1 Connecting High AC/DC Power To connect a high AC/DC power supply to the device, do the following: CAUTION! Electrical hazard – risk of damage to equipment. Do not connect AC power cables to terminals for DC power. -
Page 19: Connecting Low Dc Power
Section 2.4.2 Connecting Low DC Power RUGGEDCOM RS900's equipped with 24 or 48 V power supply inputs feature reverse polarity protection and dual power supply inputs allowing the device to accept redundant connections to a single DC power supply. To connect a low DC power supply to the device, do the following: NOTE Torque all terminal connections to 0.6 N·m (5 lbf-in). -
Page 20: Connecting The Failsafe Alarm Relay
Control of the failsafe relay output is configurable through ROS. One common application for this relay is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for the RUGGEDCOM RS900. The following shows the proper relay connections. -
Page 21: Connecting To The Device
Connecting to the Device The following describes the various methods for accessing the ROS console and Web interfaces on the device. For more detailed instructions, refer to the ROS User Guide for the RUGGEDCOM RS900. IMPORTANT! Ethernet cables should be only be connected/disconnected in a non-hazardous area, or when the device is not energized. -
Page 22: Cabling Recommendations
Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions. -
Page 23: Communication Ports
RUGGEDCOM RS900 Chapter 3 Installation Guide Communication Ports Communication Ports The RUGGEDCOM RS900 can be equipped with various types of communication ports to enhance its abilities and performance. Figure 10: Port Assignment 1. Ports 1 to 6 2. Ports 7 and 8 3. Port 9 Port... -
Page 24: Specifications
Chapter 3 RUGGEDCOM RS900 Communication Ports Installation Guide WARNING! Electric shock hazard – risk of serious personal injury and/or equipment interference. If shielded cables are used, make sure the shielded cables do not form a ground loop via the shield wire and the RJ-45 receptacles at either end. -
Page 25: Fiber Optic Ethernet Ports
RUGGEDCOM RS900 Chapter 3 Installation Guide Communication Ports Section 3.2 Fiber Optic Ethernet Ports Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Registered Jack), LC (Lucent Connector), SC (Standard or Subscriber Connector) or ST (Straight Tip) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. - Page 26 RUGGEDCOM RS900 Chapter 3 Installation Guide Communication Ports Fiber Optic Ethernet Ports...
-
Page 27: Technical Specifications
RUGGEDCOM RS900 Chapter 4 Installation Guide Technical Specifications Technical Specifications This section provides important technical specifications related to the device. CONTENTS • Section 4.1, “Power Supply Specifications” • Section 4.2, “Failsafe Relay Specifications” • Section 4.3, “Copper Ethernet Port Specifications” • Section 4.4, “Fiber Optic Ethernet Port Specifications”... -
Page 28: Failsafe Relay Specifications
Auto-crossover and auto-polarity. Typical distance. Dependent on the number of connectors and splices. RMS 1 minute. Section 4.4 Fiber Optic Ethernet Port Specifications The following details the specifications for fiber Ethernet ports that can be ordered with the RUGGEDCOM RS900. Failsafe Relay Specifications... -
Page 29: Operating Environment
To convert from peak to average, subtract 3 dBm. • Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associate when determining maximum segment distances. Tx (dBm) -
Page 30: Mechanical Specifications
Chapter 4 RUGGEDCOM RS900 Technical Specifications Installation Guide Section 4.6 Mechanical Specifications Parameter Value Dimensions Refer to Chapter 5, Dimension Drawings Weight 1.2 kg (2.7 lbs) Ingress Protection IP40 (1 mm or 0.04 in objects) Enclosure 20 AWG Galvanized Steel Mechanical Specifications... -
Page 31: Dimension Drawings
RUGGEDCOM RS900 Chapter 5 Installation Guide Dimension Drawings Dimension Drawings NOTE All dimensions are in millimeters, unless otherwise stated. 65.3 116.59 7.87 Figure 17: Overall Dimensions... - Page 32 Chapter 5 RUGGEDCOM RS900 Dimension Drawings Installation Guide 130.2 13.64 101.6 11.2 78.74 120.65 Figure 18: Panel and DIN Rail Mount Dimensions...
-
Page 33: Certification
RUGGEDCOM RS900 Chapter 6 Installation Guide Certification Certification The RUGGEDCOM RS900 device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. CONTENTS • Section 6.1, “Approvals” • Section 6.2, “EMC and Environmental Type Tests”... -
Page 34: Csa/Sira
Chapter 6 RUGGEDCOM RS900 Certification Installation Guide • CAN/CSA-C22.2 No. 60079-15:12 Electrical Apparatus for Explosive Gas Atmospheres – Part 15: Construction, Test and Marking of Type of Protection N Electrical Apparatus • UL 60079-0, Edition 6.0 (2013) Explosive Atmospheres – Part 0: Equipment – General Requirements •... -
Page 35: European Union (Eu)
Information Technology Equipment – Radio Disturbance Characteristics – Limits and Methods of Measurement The device is marked with a CE marking and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens Canada Ltd. For contact information, refer to “Contacting Siemens ”... -
Page 36: Industry Canada
RUGGEDCOM RS900 Certification Installation Guide Section 6.1.6 Industry Canada This device is declared by Siemens Canada Ltd to meet the requirements of the following Industry Canada standard: • CAN ICES-3 (A)/NMB-3 (A) Section 6.1.7 Other Approvals This device meets the requirements of the following additional standards: •... - Page 37 EMC Immunity Type Tests per IEEE 1613 NOTE The RUGGEDCOM RS900 meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports. Class 1 allows for temporary communication loss, while Class 2 requires error-free and interrupted communications.
-
Page 38: Environmental Type Tests
Chapter 6 RUGGEDCOM RS900 Certification Installation Guide Description Test Levels Enclosure Contact ± 8 kV Enclosure Air ± 15 kV Radiated RFI Enclosure Ports 35 V/m Fast Transient Signal Ports ± 4 kV @ 2.5 kHz DC Power Ports ± 4 kV AC Power Ports ±...