PASCO PASPORT PS-2230 Instruction Manual

PASCO PASPORT PS-2230 Instruction Manual

Advanced water quality sensor

Advertisement

Quick Links

Advanced Water Quality Sensor
Included Equipment
Advanced Water Quality Sensor
Stainless Steel Temperature Probe
Conductivity Electrode (10x)
Optical Dissolved Oxygen Probe
pH Electrode
Required Equipment
PASPORT Interface and Software
Optional Equipment
Optical Dissolved Oxygen Probe Metal Guard
Skin/surface Temperature Probe
Conductivity Electrode (1x)
Various Ion-selective Electrodes (ISE)
Oxidation Reduction Potential (ORP) Electrode CI-6716
Replacement Item
Optical Dissolved Oxygen Probe Sensor Cap
®
PS-2230
Part Number
PS-2230
PS-2153
PS-2571
003-14185
PS-2573
See PASCO catalog or
Part Number
PS-2588
PS-2131
699-06620
See PASCO catalog or
Part Number
PS-2587
Instruction Manual
012-14325A
www.pasco.com
www.pasco.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PASPORT PS-2230 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PASCO PASPORT PS-2230

  • Page 1 Conductivity Electrode (10x) PS-2571 Optical Dissolved Oxygen Probe 003-14185 pH Electrode PS-2573 Required Equipment PASPORT Interface and Software See PASCO catalog or www.pasco.com Optional Equipment Part Number Optical Dissolved Oxygen Probe Metal Guard PS-2588 Skin/surface Temperature Probe PS-2131 Conductivity Electrode (1x)
  • Page 2 Temperature the pH/ISE/ORP port. Follow the instructions below to set up the sensor with PASCO Capstone, SPARKvue, SPARK SLS, or the Xplorer GLX (standalone). For detailed information about each of the multi-sensor’s component sensors, see the following pages.
  • Page 3: Measuring Temperature

    The measurement can be displayed in units of °C, °F, or K. You can use the included stainless steel probe or a different probe, such as the Fast-response Probe (PS-2135) or Skin/Surface Probe (PS-2131). PASCO physics apparatus containing an embedded 10 k thermistor can also be connected to the multi-sensor. The multi-sen- sor automatically detects the presence of a temperature probe, and it will only collect temperature data if a probe is connected.
  • Page 4: Measuring Conductivity

    A d v a n c e d W a t e r Q u a l i t y S e n s o r C onductivity or on the interface select the Conductivity (10x) or Conductivity (1x) measurement, depending on which electrode you are using.
  • Page 5 M o d e l N o . P S - 2 2 3 0 p H / I S E / O R P pH/ISE/ORP The pH/ISE/ORP input of the multi-sensor is a specialized voltage sensor. Its BNC connector accepts the included pH electrode, as well as ISE and ORP electrodes (not included).
  • Page 6: Dissolved Oxygen

    A d v a n c e d W a t e r Q u a l i t y S e n s o r D i s s o l v e d O x y g e n If these steps fail to improve the response of the electrode, replace it.
  • Page 7: Dissolved Oxygen Calibration

    Sensor Cap (PS-2587), then the Sensor Cap Calibration Code Coefficients (included with the new Sensor Cap) will need to be entered into the sensor using the PASCO data acquisition software. The sensor will then need to be re-calibrated. (See Appendix B.) For a one-point calibration, you will need one “known standard”...
  • Page 8: Probe Care And Maintenance

    Sensor Cap may be extended by keeping it clean and properly stored between uses. The replacement for the Optical Dissolved Oxygen Probe Sensor Cap is model num- ber PS-2587 (see www.pasco.com for more information). NOTE: Do not remove the Sensor Cap except to replace it with a new cap.
  • Page 9: Appendix A: Specificationsreference

    M o d e l N o . P S - 2 2 3 0 S p e c i f i c a t i o n s R e f e r e n c e S o l u t i o n s f o r C o n d u c t i v i t y C a l i b r a t i o n Appendix A: SpecificationsReference General Included Sensors...
  • Page 10: Appendix B: Optical Dissolved Oxygen Probe Replacement Cap Calibration

    Alternatively, a two-point calibration could be performed using two calibration stan- dard solutions. Refer to the User’s Guide or Online Help for the PASCO software, or go to the PASCO web site at www.pasco.com and enter “Optical Dissolved Oxygen Sensor” or “PS-2196”...
  • Page 11 Click “OK” to close the Proper- ties window. Perform a one-point or a two-point calibration. (Go to the PASCO web site at www.pasco.com and enter “Optical Dissolved Oxygen Sensor” or “PS-2196” in the Search window. Download the instruction manual PDF file under the User Resources tab.)
  • Page 12 Perform a one point or two point cali- bration with “known standard” solu- tions. (Go to the PASCO web site at www.pasco.com and enter “Optical Dissolved Oxygen Sensor” or “PS-2196” in the Search window. Download the instruction man- ual PDF file under the User Resources tab.) ®...
  • Page 13 M o d e l N o . P S - 2 2 3 0 O p t i c a l D i s s o l v e d O x y g e n P r o b e R e p l a c e m e n t C a p C a l i b r a t i o n SPARKvue: Calibration Code Coefficients In SPARKvue, touch or click the “DO2...
  • Page 14: Software Requirements

    PASCO Capstone: 1.2 • SPARKvue: 2.1.3 • SPARK SLS: v1.4.1 • Xplorer GLX: v1.54 For the latest and most complete information about minimum software requirements, go to www.pasco.com. Enter “PS-2230” in the “Search” window to go to the product page. ® 012-14325A...
  • Page 15: Technical Support

    PASCO, PASCO scientific, Capstone, SPARKvue/SPARK SLS, MultiMeasure Sensors, PASPORT, and Xplorer GLX are trademarks or registered trademarks of PASCO scientific, in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of, their respective owners. For more information visit www.pasco.com/legal.
  • Page 16 A d v a n c e d W a t e r Q u a l i t y S e n s o r T e c h n ic a l S u p p o r t ®...

Table of Contents