Specifications; Standard Accessories - Hitachi DN 12DY Handling Instructions Manual

5) Battery tool use and care
a) Recharge only with the charger specifi ed by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fi re when used with
another battery pack.
b) Use power tools
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, fl ush with water. If
liquid contacts eyes, additionally seek medical
help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach
of children and infi rm persons.

SPECIFICATIONS

POWER TOOL
Model
No-load speed
Drilling
Capacity
Driving
Rechargeable battery
Weight
CHARGER
Model
Charging voltage
Weight
only with specifi cally
Wood
(Thickness 18 mm)
Metal
(Thickness 1.6 mm)
Wood screw
UC14YFA
7.2 – 14.4 V
0.6 kg
PRECAUTIONS FOR CORDLESS ANGLE DRILL
1. Always charge the battery at a temperature of 10 –
40°C. A temperature of less than 10°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C.
The most suitable temperature for charging is that of 20
– 25°C.
2. When one charging is completed, leave the charger at
least 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the battery.
6. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
7. When drilling in wall, fl oor or ceiling, check for buried
electric power cord, etc.
8. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose of
the exhausted battery.
9. Using an exhausted battery will damage the charger.
10. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or infl ammables into the charger
air ventilation slots will result in electrical shock hazard
or damaged charger.
11. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
12. Do not wear gloves made of stuff liable to roll up such as
cotton, wool, cloth or string, etc.
13. Do not insert object into the air ventilation slots of the
body.
DN12DY
0 – 800 min
18 mm
Steel: 10 mm,
Aluminum: 10 mm
5.1 mm (diameter) × 40 mm (length)
EB1220BL: Ni-Cd battery, 12 V (2.0 Ah, 10 cells)
EB1226HL: Ni-HM battery, 12 V (2.6 Ah, 10 cells)
EB1230HL: Ni-MH battery, 12 V (3.0 Ah, 10 cells)
1.4 kg

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains
the accessories listed in the table below.
① Plus driver bit (No. 2) .................................................... 1
② Charger (UC14YFA) ..................................................... 1
③ Plastic case .................................................................. 1
④ Battery ................................................................... 1 or 2
Standard accessories are subject to change without notice.
English
-1
5