Advertisement
**For customers outside the U.S. or Canada, please contact the store for assistance.**
WARNING
Failure to comply with any of the warnings
in these instructions may result in serious
personal injuries such as cuts, broken
bones, nerve damage, paralysis, brain
injury, or death. Failure to comply may
also result in property damage. Please
heed all warnings and cautions. To ensure
your safety, do not attempt to assemble
this system without reading and following
all instructions carefully. Identify and
inventory the parts using the Parts List.
INSTRUCTION #1030931
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
REEBOK XL ACTION GRIP
BASKETBALL SYSTEM
MODEL #51549
Assembly INSTRUCTIONS AND
OWNER'S MANUAL
Save this instruction in the event that
the manufacturer has to be contacted for
replacement parts.
®
9/17/2007
Advertisement
Table of Contents
Related Manuals for Reebok 51549
Summary of Contents for Reebok 51549
- Page 1 Identify and inventory the parts using the Parts List. INSTRUCTION #1030931 **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, REEBOK XL ACTION GRIP BASKETBALL SYSTEM MODEL #51549 ASSEMBLY INSTRUCTIONS AND OWNER’S MANUAL Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
-
Page 2: Parts List
PARTS LIST Part # Description 1030702 Top Pole 1030703 Middle Pole 1030855 Bottom Pole 1030781 Right Backboard Bracket 1030762 Left Backboard Bracket 1030881 Backboard 500096 Pole Cap 502005 502056 Plastic Guard 504068 Counterbalance Spring 510025 1/2” x 21 3/4” Axle CB01599 Base 510022... -
Page 3: Parts List
PARTS LIST Part # Description A040031C Inner Channel 1030812 Outer Tube C050018 Channel Stop 1030748 Pole Bracket C050019 Handle C050017 Trigger Action Grip Hardware (HH01300) ® A070044 Lock Tab B070040 1/4-20 x 1 1/2” Screw B080015 Trigger Spring BW00100 #6 Flat Washer 300027 5/16”... -
Page 4: Safety Instructions
Failure to follow these safety instructions may result in serious injury or property damage and will void the warranty. The owner must ensure that all players know and follow these rules for safe operation of the system. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. -
Page 5: Assembly
Top Pole: Four holes at the top of the pole and one small hole at the bottom. 9/16” Wrenches 1005748 HH01300 Identify the pole sections before beginning assembly. Failure to assemble the pole sections correctly may result in severe personal injury or property ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY Middle Pole: One slot at the top of the pole,... - Page 6 1005748 PB (1) This step cannot be reversed. In order to seat the poles, strike each end of the pole very hard 5 to 6 times on a piece of scrap wood or cardboard. This must be done even if the poles cover the slots before seating.
- Page 7 1/2” Wrenches Make sure the Rubber Gasket is inside the Base Cap (AH). 9/16” Wrenches 1006763 Screw the Base Cap (AH) onto the Base. BB (2) BA (1) The Bracket on the Middle Pole faces the Base. Rubber Gasket Completely tighten all Base and Pole Brace hardware.
- Page 8 1/2” Wrenches 7/16” Wrench HD9125B Completely tighten the Nuts (HA). now, before proceeding with this step. 1012253 You may want to perform step #36 The Tap Bolts (RE) should be at the outer edge of the holes. Tighten the T-Nuts (RA) only until the Rubber Washers (RD) begin to bulge.
- Page 9 1/2” Wrenches Tightening these Nuts later will adjust 3/4” Wrenches 1012253 (Not actual size) Only hand tighten the Nuts (HH). HD9125B Do not overtighten the Nuts (HH). Completely tighten all Rim hardware. the Rim tension. Bend the Backboard Brackets (LB &...
- Page 10 3/4” Wrenches HD9125B Tighten the Nut until it is flush with the Bolt. HH01300 (Not actual size) (Not actual size) Attach this end of the Long Extension Arms (AL) to the Backboard Brackets TWo PeoPLe ReQuIRed FoR THIs sTeP The Backboard and Rim should be on the ground resting on cardboard with the Extension Arms facing up.
- Page 11 1/2” Wrenches Remove the Inner Channel (AN) that is packaged inside the Outer Tube (AO) before attaching the Handle (AR). HH01300 GB (2) Squeeze the Trigger while inserting the Inner Channel (AN). Insert the slotted end first. Slide the Inner Channel (AN) up to the 10’...
- Page 12 TWo PeoPLe ReQuIRed 3/4” Wrenches FoR THIs sTeP. 9/16” Wrenches HD9125B Use the holes closest to the pole. Tighten all Nuts securely now. Tighten all Nuts securely now. Hook the Springs (AD) into the #3 holes in the Backboard Brackets. Attach the Net (AB).
- Page 13 WARNING Never put the system in an upright position without proper weight in the Base. The system may fall over and could result in serious personal injury or property damage. Two adults are required to complete assembly. To prevent serious injuries, the pole should be held down by one adult at all times while filling the Base.
- Page 14 WHEN USING WATER IN THE BASE TAKE THE FOLLOWING PRECAUTIONS: 1. Make sure the surface beneath the Base is smooth and free of stones, gravel or other sharp objects that could puncture the Base and cause leakage. 2. Check the Base frequently for cracks or punctures. 3.