hager 04011 User Instructions

™ §
Programmable light
sensitive switch
EE110, 04011
Operating principle Description
The EE110, 04011 programmable light sensi- The programmable light sensitive switch EE110,
tive switch controls light sytems according to 04011 has two main functions:
a program set by the user, depending on
• a light sensitive switch comprising:
natural illumination;
Œ
Override selector switch to allow permanent
- during the work authorization period,
setting ON or OFF , auto or test mode.
depending on wheter the measured light

level is below or above the order, it will be Lighting range selector
Ž
switched on or off.
Potentiometer to set light level
- during the work banning period, the

Indicator to show output switching.
contact remains without tension, whatever
the light level is.
The light sensitive switch includes a built
in time delay which avoid unnecessary
switching due to temporary factors such
as car beams etc... Ž
Lux

T
6:00 8:00 17:00 23:00
• a programmer to establish the automatic operating
20
ON ON
19
cycle.
18
OFF OFF OFF
Time setting
1
User instructions
Programming
Switching dial
Work
banning
period
OFF
Work
authorization
ON
period
Permanent overrides
 Œ
the override selector allows permanent
overrides which have priority on programming
and the measured light level.
auto
permanent override "ON"
Œ
test
auto
permanent override "OFF"
test
Setting of the working level
Œ
the "test" position of the override selector
makes easier the setting of the working level,
it removes the ON and OFF delay.
Select the sensitivity range which suits whith

the application (selector ) :
5 to 100 lux (low light level) applica-
tion examples : public lighting, shop
windows, signals....
50 to 2000 lux (high light level) appli-
cation examples : control of shades.
At the appropriate moment of the day, put the
Œ
selector in "test" position; turn the poten-
Ž
tiometer up to the switching point (the

indicator lights); put the selector back to
position "auto", the normal operating mode of
the device.
Mounting of the cell
To ensure a good working of the light sensitive
switch, the cell must not be influenced by
artificial light or direct solar radiation and has
to be sheltered from dust and humidity.
In case of disconnection of the link between
the cell and the light sensitive switch, the
output of the device will be switched on.
Make sure the light sensitive switch is unplug-
ged before connecting the cell.
Technical specification
Electrical specification:
- voltage rating : 230V ~+10/-15% 50 Hz
- consumption : 1,5 VA max.
- output : 1 voltage free changeover contact
Max. breaking capacity :
AC1 16A 250V~
incandescent lamp 2000W 230V~
halogen lamp 1000W 230V~
fluorescent lamp :
uncompensated 1000W 230V~
compensated in series (10μF) 1000W 230V~
// compensated (15μF) 200W 230V~
duo : 1000W 230V~
Functional characteristics:
- 2 sensitivity ranges 5 to 100 lux,
50 to 2000 lux
- daily cycle
- program setting : 15 minutes increments
- accuracy : ± 6 min./ annum
- operating reserve : at 20°C, 200 h after
beeing connected for 120 h
- ON and OFF delay : 15 to 60 s.
- working temperature :
-30 °C to +60 °C (cell),
-10 °C to +50 °C (modular device)
- storage temperature :
- 20 °C to +60 °C
- protection class (cell) : IP54
- insulation class (cell) : II
Connection capacity:
- modular device: 0,5 to 4 mm 2
- cell : 0,75 to 2,5 mm 2
- Max. lenght between cell and modular
device : 50 m
- mounting of the cell with 2 screws Ø 2,5 mm.
L
N
18 19 20
5 6 9 10
Warranty GB
A warranty period of 24 months is offered on hager products,
from date of manufacture, relating to any material of manufac-
turing defect. If any product is found to be defective it must be
returned via the installer and supplier (wholesaler).
The warranty is withdrawn if :
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary to
IEE wiring regulations and accepted practice within the indus-
try at the time of installation.
- the procedure for the return of goods has not been followed.
Explanation of defect must be included when returning goods.
6E 7518.f