In the interest of improving internal design, operational function, and/or reliability, NETSYS reserves the right to make changes to the products described in this document without notice. NETSYS does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Use ONLY the dedicated power supply for your device. Connect the power to the right supply voltage (110V AC used for North America and 230V AC used for Europe. NV-700L supports 12 VDC power input). Place connecting cables carefully so that no one will step on them or stumble over them. DO NOT allow anything to rest on the power cord and do NOT locate the product where anyone can work on the power cord.
Page 4
Internet access and advanced voice services including VoIP, over a standard copper telephone cable. NV-700L is seen by many operators as an ideal accompaniment to a FTTP rollout, where for instance fiber optic is supplied direct to an apartment block and from there copper cable is used to supply residents with high-speed VDSL2.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Chapter 1. Unpacking Information 1.1 Check List Thank you for choosing Netsys NV-700L Before installing the router, please verify the contents inside the package. Package Contents: 1 x VDSL2 CO Modem 1 x QR code for user’s...
• Do not install phone lines strapped together with AC power lines, or telephone office line with voice signal. • Avoid installing this device with radio amplifying stations nearby or transformer stations nearby. • Please note that the voice spectrum allowed by the NV-700L internal splitter is 0 KHz ~ 120 KHz.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 2.3 General Rules Before making any connections to the modem, please note the following rules: • Ethernet Port interface : RJ-45 All network connections to the modem Ethernet port must be made using Category 5 UTP/STP or above for 100 Mbps, Category 3, 4 UTP for 10Mbps.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 2.4 Connecting the RJ-11 / RJ-45 Ports The line port have 1 connector: RJ-11 . It is used to connect with NV-700L (CO) over a single pair phone wire to NV-720R CPE(Slave) side (point to point application).
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 2.5 VDSL2 Application First a quick overview on a complete setup of VDSL2 CO/CPE Modem. NV-700L/NV-720R is a modem leverages the extraordinary bandwidth promise of VDSL2(max 100Mbps Symmetric) technology (Figure 2.2)
Page 13
2.5.1 Connect the NV-700L and the NV-720R to the Line The objective for VDSL2 is to pass high speed data over a twisted pair cable. In the setup, connect NV-700L to NV-720R through phone wire(24~26 AWG) or line simulator or any other hardware representation of a cable network, with or without noise injection and crosstalk simulations.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Chapter 3. Hardware Description This section describes the important parts of the vdsl2 Modem It features the front panel and rear panel. NV-700L Outward...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 3.1 Front Panel The figure shows the front panel. (Figure 3.1) Figure 3.1 Front Panel(NV-700L) 3.2 Front Indicators The Modem has Seven LED indicators. The following Table shows the description. (Table...
Page 16
Note: It is normal for the connection between two Modems to take up to 3 minutes, due to NV-700L/NV-720R to establish a link mechanism in auto-negotiation, with detects and calculates CO and CPE both PBO and PSD level, noise levels and other arguments for getting...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 3.3 Rear Panel The following figure shows the rear panel. (Figure 3.2) Figure 3.3 Rear Panel And the table shows the description. (Table 3-2) Table 3-2 Description of the modem rear connectors...
Page 18
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Type Connector Description phone RJ-11 For connecting to the POTS equipment or ISDN. Ethernet RJ-45 For connecting to an Ethernet equipped device. (E1-E4) USB2.0 Type A For connecting to the USB dongle.
Chapter 4. Configure the NV-700L Via Web Browser The NV-700L provides a built-in HTML based management interface that allows configuration of the NV-700L via Internet Browser. Best viewed using Chrome or Firefox browsers. In order to use the web browser to configure the device, you may need to allow: •...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 4.1 BASIC Setup Login webpage The IP address is 192.168.16.249 , username and password are admin. Figure 4.1 Login Password...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Display status The status page displays some information. When the device is running. For example: Device Information:...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Application->multicast IGMP setting According to the setting, if you want to test IGMP function, you only need to enable IGMP function basic on the Application SETUP...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 APPLICATION->SNMP Below is picture for how to enable SNMP function, device support SNMP V1/V2...
Page 51
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Download “MG-SOFT MIB Browser”. below is picture for how to use the software. Connect Remote SNMP agant.
Page 52
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Select OID:1.3.6.1.2.1.1.3 System Up Time...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 4.8 USB setup USB-Storage Device Info Insert a U disk into the USB interface, then login 192.168.16.249,select “USB”->” Storage Device Info”. Confirm the system has mounted the U disk.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 USB-> FTP Client Below is picture for how to enable FTP Client function. Input FTP Client Settings, then chick “Download”...
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Click “Refresh”, Make sure the status is complete. USB-> TFTP Server Below is picture for how to enable TFTP Server function.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Appendix A: Cable Requirements A.1 Ethernet Cable A CAT 3~7 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet device to the Modem. A 10Base-T cable often consists of four pairs of wires, two of which are used for transmission. The connector at the end of the 10Base-T cable is referred to as an RJ-45 connector and it consists of eight pins.
Page 60
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Figure A-2 Pin Assignments and Wiring for an RJ-45 Straight-Through Cable Figure A-3 Pin Assignments and Wiring for an RJ-45 Crossover Cable...
Page 61
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 A.2 Telephone wire Standard telephone wire of any gauge or type-flat, twisted or quad is used to connect the Modem to the telephone network. A telephone cable typically consists of three pairs of wires, one of which is used for transmission. The connector at the end of the telephone cable is called an RJ-11 connector and it consists of six pins.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Appendix B: Product Specification Key Features & Benefits Adopts ARM Cortex A9 dual-core processor Supports G.998.4 G.INP Supports up to 100 Mbps symmetric Support 8 bands selectable Support USB 2.0 for connecting USB Dongle...
Page 63
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Support CO side bridge mode Supports Dual Firmware Image Backup Supports SNMP v1/v2 On board POTS/ISDN splitter Supports TR-069 Note: 1. Features and specifications in this manual are subject to change without prior notice.
Page 64
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Product Specification IEEE802.3/802.3u standards Standard: ITU-T G992.1/G992.3/G992.5/G993.1/ G993.2/G998.4 standards 4 x RJ-45 10/100 Mbps Ethernet port 1 x RJ-11 / Terminal combo for VDSL2 line port Physical Interface: 1 x RJ-11 connector for POTS/ISDN device 1 x Reset Button for resetting to factory default 1 x USB2.0 for connecting USB dongle...
Page 65
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 -20°C ~ 70°C (-4°F ~158°F) Storage Temperature: Humidity: 10% to 90% (non-condensing) About 0.4 kgs Weight: Dimensions: 184 x 146 x 40 mm ( 7.2" x 5.74" x 1.57”)
Solution: 2.4 Check the modem on the attached device and cable connections for possible defects. 2.5 Make sure that the phone wire must be connecting NV-700L first, when powered on. 2.6 Replace the defective modem or cable if necessary. 2.7 Or try to change band profile as 17a for getting long reach...
Page 67
VDSL setting failure or phone cable length is over the specification limit. 3.1 Please make sure that the phone wire must be connected between NV-700L(CO) side and CPE side when both are power on. NV-700L(CO) side will do link speed function depending on phone wire length, therefore if NV-700L(CO) side can’t detect CPE Side over phone wire while...
Page 68
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 The protocol was standardized in the International Telecommunication Union telecommunications sector (ITU-T) as Recommendation G.993.2. It was announced as finalized on 27 May 2005,[1] and first published on 17 February 2006. Several corrections and amendments were published in 2007 through 2011.
Page 69
IPERF program, and TCP window size must be settled max. 64k, the parameter as iperf –c server IP address –i 1 –t 50 –w 65535 for client side. I just bought a NV-700L to replace my Quest DSL modem for my home. I was told any VDSL2 modem 6. Question: would replace and give me higher communication speeds.
Page 70
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 We need to set up a default gateway on a NV-700L pair which are in Bridge mode, as they want to 7. Question: manage the units from a different network. When the application is used within the LAN, the switch(bridged) mode is not necessary to set up a gateway .However, if the application crosses various network segments (LAN to WAN or WAN to...
Page 71
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 9. Question: What is the maximum Ethernet frame MTU for these modems? Answer: NV-700L maximum Ethernet frame MTU is 1518 bytes.
Page 72
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 System Diagnostics Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section. However, if the unit power is off after running for a while, check for loose power connections, power losses or surges at the power outlet.
Page 73
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Physical Configuration If problems occur after altering the network configuration, restore the original connections, and try to track the problem down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation do not exceed recommendations.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Appendix E: Compliance Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 of FCC rules.
Page 75
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service.
Page 76
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol.
NV-700L VDSL2 Single Master Modem USER’S MANUAL Ver. A.2 Warranty The original product that the owner delivered in this package will be free from defects in material and workmanship for one year parts after purchase. There will be a minimal charge to replace consumable components, such as fuses, power transformers, and mechanical cooling devices.