Page 2
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Safety Warnings For your safety, be sure to read and follow all warning notices and instructions before using the device. DO NOT open the device or unit. Opening or removing the cover may expose you to dangerous high voltage points or other risks.
Page 3
FTTdp rollout, where for instance fiber optic is supplied direct to an apartment block and from there copper cable is used to supply residents with high-speed G.fast. Caution: The NV-450M/ NV-450S is for indoor applications only. This product does not have waterproof protection, please do not use in outdoor applications.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Chapter 1. Unpacking Information 1.1 Check List Thanks for choosing NV-450M/NV-450S. Before installing the modem, please verify the contents inside the package. Package Contents: 1 x Modem 1 x QR code for user’s...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Chapter 2. Installing the Modem 2.1 Hardware Installation This chapter describes how to install the modem, and establish the network connections. The NV-450S may be installed on any level surface (e.g.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 2.3 General Rules Before making any connections to the modem, please note the following rules: • Ethernet Port interface : RJ-45 All network connections to the modem Ethernet port must be made using Category 5e UTP/STP or above for 1000 Mbps, Category 5 UTP or above for 100Mbps Category 3, 4 UTP or above for 10Mbps.
2.4 Connecting the RJ-11 / RJ-45 Ports There are two type line: 1 Terminal Block & 1 RJ-11 connector. It is used to connect with NV-450M Master side over a single pair phone wire to NV-450S Slave side (point to point application).
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 2.5 Point to Point Application First a quick overview on a complete setup of LAN extender Master/Slave LAN extender. NV-450M/NV-450S is a LAN extender leverages the extraordinary bandwidth promise of G.fast technology (max. 1Gbps) (Figure 2.2)
Page 12
2.5.1 Connect the NV-450M(Master) and the NV-450S(Slave) to the Line The objective for LAN extender is to pass high speed data over a twisted pair cable. In the setup, connect NV-450M(Master) to NV-450S (Slave) through phone wire(24~26 AWG) or line simulator or any other hardware representation of a cable network, with or without noise injection and crosstalk simulations.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Chapter 3. Hardware Description This section describes the important parts of the NV-450M/S. It features the front panel and rear panel. NV-450 Physical appearance...
Model as MV-450M, and LED Off indicates firmware Model as NV-450S. 2. If want to change NV-450M to NV-450S Model, just update firmware to NV-450S. The reverse is also do the same step. Fireware update menu please refer to administration webpage on page 30...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 3.2 Front Indicators The Modem has Seven LED indicators. The following Table shows the description. (Table 3-1) Table 3-1 LED Indicators Description and Operation Color...
Page 16
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 On(Steady) The xDSL connection is up. xDSL (xDSL LED for Green Fast Blinking The Master device has detected a Slave device and ready to connect.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 3.3 Rear Panel The following figure shows the rear panel. (Figure 3.2) Figure 3.3 Rear Panel And the table shows the description. (Table 3-2) Table 3-2 Description of the modem rear connectors...
Page 18
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Type Connector Description phone RJ-11 For connecting to the POTS equipment or ISDN. Ethernet RJ-45 For connecting to an Ethernet equipped device. (E1-E4) USB3.0 USB Type A For connecting to the USB dongle.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 3.4 Back sticker Note : 1.Default factory model shown as back sticker inclusing default model name, S/N、FCC CE Mark, Input DC voltage information, User’s maunal download QR code, made of origin, default LAN IP and...
Chapter 4. Configure the modem via Web management menu The NV-450M/ NV-450S provides a built-in HTML based management interface that allows configuration of the NV-450S via Internet Browser. Best viewed using Chrome or Firefox browsers. In order to use the web browser to configure the device, you may need to allow: •...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.1.2 Display status When the device is running, the status page will display the device informations (Internet Status, Software Version and DSL Line Status etc.), as shown in Figure 4.1.2.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2 Select the Menu Basic There is an easy Setup for end users at the setup of NV-450M with G.fast, LAN, System, Routing and NV-450S with WAN Internet, DSL, LAN, System, Routing for more detail configurations...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.1 WAN Internet This page allows you to view and configure various Internet connections Figure 4.2.1 WAN Internet information...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.2.2 Status This page provides the various status and statistics information Figure 4.2.2.2 Status...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.3 LAN 4.2.3.1 Configuration Configuration support to provide IP address to devices connected on the LAN side of the CPE. Applicable for all wired and wireless devices that requests for dynamic IP address.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.3.2 Devices Connected List of Clients Connected on the LAN Side of the device Figure 4.2.3.2 Devices Connected...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.4 System 4.2.4.1 Administration This page allows users to take configuration backup, restore to previous configuration or to factory settings, upgrade firmware and reboot device.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.2.4.3 System Time Configuration to enable the device to synchronize the system time with the time servers. Figure 4.2.4.3 System Time...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.3 Select the Menu Advanced Select “Advanced”. The menu below will be used frequently. NV-450M includes the sub-menus of UPnP、 USB/SATA、Device Management. NV-450S includes the sub-menus of Multicast、Dynamic...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.3.2 Dynamic DNS Dynamic DNS allows the user to update wan IP address with one or many dynamic DNS services. So anyone can access services on computer using DNS-like address.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.3.4 QoS Quality of Service (QoS) settings enables you to manage and optimize the performance of the applications. It shapes the network traffic and prioritizes the devices and services by controlling the bandwidth...
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 4.3.5 Tunneling 6rd is a mechanism to facilitate IPv6 rapid deployment across IPv4 infrastructures of Internet service providers (ISPs). DSLite is a mechanism to facilitate IPv4 deployment across IPv6 infrastructure.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Appendix A: Cable Requirements A.1 Ethernet Cable A CAT 3~7 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet device to the Modem. A: 10/100TX cable often consists of four pairs of wires, two of which are used for transmission.
Page 47
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Figure A-2 Pin Assignments and Wiring for an RJ-45 Straight-Through Cable Figure A-3 Pin Assignments and Wiring for an RJ-45 Crossover Cable...
Page 48
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 A.2 Telephone wire Standard telephone wire of any gauge or type-flat, twisted or quad is used to connect the Modem to the telephone network. A telephone cable typically consists of three pairs of wires, one of which is used for transmission.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Appendix B: Product Specifications Key Features & Benefits Compliant with IEEE 802.3 / 802.3u / 802.3ab Ethernet Standard Compliant with ITU-T G993.2 VDSL2 standard (NV-450S only) Compliant with ITU-T G998.4 G.INP standard (NV-450S only)
Page 50
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Support TR-0693. Support RJ-11 / Terminal block combo line port On board POTS/ISDN splitter Support Jumbo frame(MTU) up to 1600 bytes Note: 1. Features and specifications in this manual are subject to change without prior notice.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Appendix C: Troubleshooting Diagnosing the Modem’s Indicators The modem can be easily monitored through its comprehensive panel indicators. These indicators assist the network manager in identifying problems the hub may encounter. This section describes common problems you may encounter and possible solutions.
Page 54
All lights come on but no Link light. Is this the complete wrong application for this unit? Re: Please note NV-450S is a Slave (CPE side), it must be connected to the NV-450M Master(CO Answer: side) or IP-DSLAM to get link.
Page 55
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 We need to set up a default gateway on a NV-450M/ NV-450S pair which are in Bridge mode, as they 5. Question: want to manage the units from a different network.
Page 56
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 7. Question: What is the maximum Ethernet frame MTU for these modems? Answer: NV-450M / NV-450S jambo frame(MTU) up to 1600 bytes.
Page 57
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 System Diagnostics Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section.
Page 58
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Physical Configuration If problems occur after altering the network configuration, restore the original connections, and try to track the problem down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation do not exceed recommendations.
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Appendix D: Compliance Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 of FCC rules.
Page 60
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service.
Page 61
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 RoHS Mark Warning RoHS stands for Restriction of Hazardous Substances, and impacts the entire electronics industry and many electrical products as well. The original RoHS, also known as Directive 2002/95/EC, originated in the European Union in 2002 and restricts the use of six hazardous materials found in electrical and electronic products.
Page 62
NV-450M/S: G.fast Master Modem+ G.fast / VDSL2 / V35b Slave Modem USER’S MANUAL Ver. A.4 Warranty The original product that the owner delivered in this package will be free from defects in material and workmanship for one year parts after purchase.