Advertisement
Available languages
Available languages
CCIC1410 MJPEG / MPEG4 / Dual-Streaming / Indoor Colour Camera
Package contents
•
1 x SIEMENS CCIC1410 IP Camera
•
1 x Documentation CD
•
1 x Utilities CD
•
1 x Installation instruction (English, German)
•
1 x Installation instruction (French, Spanish, Italian)
•
1 x Power adapter
•
1 x Wall/Ceiling bracket
•
1 x Ethernet cable (1:1, 2 m)
•
2 x Wall plugs
•
2 x Mounting screw
Target readers
The instructions in this document are designed only for the
following target readers:
Target
Qualification
Activity
readers
Installer Technical
Installs the
training for
product,
electrical
individual
installations.
components of
the product or
replacement
parts.
General safety precautions
•
Read the general safety precautions before installing,
configuring and operating the device.
•
Keep this document for reference.
•
Always pass this document on together with the product.
•
Please also take into account any additional country-
specific, local safety standards or regulations concerning
project planning, operation and disposal of the product.
•
Follow all warnings and instructions marked on the
device.
•
Do not attempt to service or modify this device yourself.
Refer this work to qualified service personnel.
Liability claim
•
Do not make any changes or modifications to the device
unless they have been approved by the manufacturer.
•
Use only spare parts and accessories that have been
approved by the manufacturer.
Installation
•
It is recommended that all preparatory work (e.g. fitting of
accessories) be carried out in a workshop prior to final
installation.
Radio interference with other devices in the environment
•
When handling modules that are susceptible to
electrostatic discharge, please observe the ESD
guidelines.
Damage due to unsuitable mounting location
•
The environmental conditions recommended by the
manufacturer must be observed. See section
Specifications.
•
Do not operate the device in dusty places.
•
Do not expose the device to mechanical vibrations or
shocks.
•
Protect the device against moisture.
•
Place the unit on a stable surface that will hold its weight.
•
The mounting surface must be solid and non-
combustible.
•
Do not operate the device close to sources of powerful
electromagnetic radiation.
Danger of electrical shock due to incorrect connection
•
Connect the device only to power sources with the
specified voltage. Voltage supply requirements can be
found on the mains adapter.
•
Make sure the device is permanently connected to the
electricity supply; a readily accessible disconnect device
must be provided.
•
This device is designed to work with 5 V DC-systems. Do
not connect the device to any other power systems
Transportation
•
Keep the packaging material for future transportation.
•
Do not expose the device to mechanical vibrations or
shocks.
2
Siemens Building Technologies
Fire Safety & Security Products
Ordering data
Type
Item Number
CCIC1410-L
S54561-C90-A1
CCIC1410-LA
S54561-C90-A2
CCIC1410-LAW S54561-C90-A3
Installing the camera
Step 1: Network deployment
Condition of the
product
Components of
the product are
not yet installed
or need to be
replaced or
modified.
1
Power
2
Digital Output
3
Digital Input
4
Ground
1.
If you have external devices such as sensors and alarms,
make connection from general I/O terminal block.
2.
Connect the camera to a switch/hub via Ethernet cable.
Use Category 5 Cross Cable when Network Camera is
directly connected to PC.
3.
Connect the supplied power adapter from the camera to
a power outlet.
Step 2: Assigning an IP address
1.
Install the CCIC1410 Installation Wizard under the
Software Utility directory from the supplied CD.
2.
The program will conduct analyses on your network
environment. After your network is analyzed, please click
on the Next button to continue the program.
3.
The program will search the SIEMENS Network Devices
in the same LAN.
4.
After searching the SIEMENS Network Devices, the main
installer window will pop up. Click on the MAC address
that matches the one labeled on the rear of your device
to connect the web browser (ex. Microsoft® Internet
Explorer, Mozilla Firefox or Netscape) to the Network
Camera.
5.
Retrieve live videos through web browsers or recording
software.
Configuring the wireless connection
(CCIC1410-LAW only)
1.
Check the SSID currently set on your wireless access
point (AP).
Note
SSID, abbreviated from Service Set Identifier, is the
name assigned to the wireless network. The
CCAC1410-LAW factory SSID setting is set to
"default".
Note
Select "Ad-Hoc" wireless mode if you want the
CCIC1410-LAW to communicate without using an AP
or wireless router.
2.
Go to CCAC1410-LAW Configuration > Wireless LAN.
3.
Type in the SSID consistent with the setting on your
access point (AP).
4.
Select the Wireless mode as Infrastructure.
5.
Click Save.
The Network Camera starts to reboot.
6.
Wait for the live image is reloaded to your browser.
7.
Unplug the power cable and Ethernet cable from the
Network Camera.
Description
1/4" VGA IP-Camera
Colour
8.
Replug the power cable to the camera.
1/4" VGA IP-Camera
Colour Audio
1/4" VGA IP-Camera
Colour Audio WLAN
1 2
3
4
For further set up, please refer to the Configuration Manual
on the supplied CD.
Care and maintenance
The camera is maintenance-free. Small amounts of dirt or
dust can be cleaned from the camera using a clean soft cloth.
•
Do not touch the lens area. Use a soft cloth moistened to
clean the surface if it is touched accidentally
Update
Specifications
Image sensor
Effective pixels
Image compression
method
Image frame rate
Min. Illumination
Synchronisation
Network connection
Internet protocol
Power requirement
Camera weight
Operating temperature
Disposal
Note
If the Ethernet cable is not connected, the camera
will switch to WLAN when it is restarted.
The Network Camera now operates in wireless mode.
For the latest camera firmware update, please refer to
the following download link:
http://www.siemens.com/cctv
1/4" CMOS sensor
640 (H) x 480 (V)
MJPEG / MPEG4 simultaneous
dual-streaming
VGA (640 x 480) at max. 30 ips
0.4 lux (F2.0)
Internal
1 x 10/100 base-T Ethernet
connection for LAN / WAN
IPv4, TCP/IP, HTTP, UPnP,
RTSP/RTP/RTCP, IGMP, SMTP,
FTP, TelNet, DHCP, NTP, DNS,
DDNS, PPPoE
5 V DC (plug-type power supply
included)
0.128 kg
0 – 40 ºC
Electrical and electronic products should be
disposed of separately from the municipal
waste stream via designated collection facilities
appointed by the government or the local
authorities.
EN
04.2009
Advertisement
