Advertisement
Available languages
Available languages
CCDA1445 Installation Instruction
Safety
Target Group
• The instructions in this document are
designed only for qualified electricians.
General Safety precautions
• Read the general safety precautions
before installing the device.
• Use the device only for its intended use.
See section Description of equipment.
• Keep this document for reference.
• Always pass this document on together
with the product.
• Please also take into account any
additional country-specific, local laws,
safety standards or regulations concerning
installation, operation and disposal of the
product.
Liability claim
• Do not connect the device to the 230 V
supply network if it is damaged or any
parts are missing.
• Use only spare parts and accessories that
have been approved by the manufacturer.
Setup
Damage due to unsuitable mounting location
• The environmental conditions
recommended by the manufacturer must
be observed. See Technical Data.
• Do not operate the device close to sources
of powerful electromagnetic radiation.
• Do not operate the device in dusty places.
• Protect the device against moisture.
Danger of electrical shock/fire hazard/damage
to the device due to incorrect connection
• Connect the device only to power sources
with the specified voltage. Voltage supply
requirements can be found on the rating
label of the device.
• Connect the device only to a limited power
source.
• Connect the equipment to 24 V AC UL
Listed Class 2 Power Supply.
• Ensure that the safety wire (located in the
dome base) is engaged.
Service and maintenance
Danger of electrical shock during
maintenance
• Do not attempt to service or modify this
device yourself. Refer this work to qualified
service personnel.
Description of equipment
CCDA1445 is a Dome camera for video
surveillance applications. It can be mounted to
a wall or ceiling indoors. When used with the
appropriate accessories it is also suitable for
installation outdoors. See Installation &
Configuration Manual for accessories
installation details.
2
Siemens Building Technologies
Fire Safety & Security Products
Technical Data
Temperature
0 to +50 °C
range, operating
Temperature
-20 to +60 °C
range, storage
Weight
1.8 kg
Power
24 V AC ± 10 %;
requirements
50 Hz
Power
20 VA
consumption
Interface
RS485 (2-wire)
Protocols*
SIEMENS, PELCO-
D/P, VCL, VICON,
KALATEL, ERNITEC,
SENSORMATIC
RS485, MONLYNX-D;
FIELDBUS, DIP-
switch selectable
Data rate
2400 bit/s, 4800 bit/s,
9600 bit/s, 19200 bit/s;
DIP-switch selectable
European
EN 61000-6-3
directives
EN 55022 class B
EN 50130-4
* 3rd party protocols may vary without further
notice
Details for ordering
Type
Item No
Description
CCDA1445
S54561-
1/4" Dome Colour
-ST18
C10-A1
18x
CCDA1445
S54561-
1/4" Dome D/N 18x
-DN18
C11-A1
CCDA1445
S54561-
1/4" Dome D/N 26x
-DN26
C12-A1
CCDA1445
S54561-
1/4" Dome D/N 36x
-DN36
C13-A1
Further products and accessories can be
found in the Internet:
siemens.com/cctv
> Catalogue Downloads.
Package contents
• Dome base
• Dome drive incl. camera
• 3 mounting screws
• BNC extension cable
• CD including detailed Installation &
Configuration Manual and Quick Start
Guides for the accessories
• Installation Instruction
Installation
1. Setup the DIP switch on Dome base and
Dome drive to select baud rate, address
and protocol (see Installation &
Configuration Manual for details).
2. Refer to Fig. A to install the dome base
and dome drive. Connect the safety wire
(3) to the hook (2) of the dome base (1)
carefully to prevent the dome from
dropping.
3. To lock the dome drive (4) to the dome
base, line up the notch (11) to the right
arrow on the label (12) then turn dome
drive to right with both hands (see figure C)
till the notch lines up to left arrow.
4. Connect BNC connector: connect BNC
extension cable (10) to BNC connector (9).
5. Connect video cable: connect BNC VIDEO
OUT cable (10) to the monitor with a coax
cable.
6. Fix video cable on BNC connector holder
(6).
7. Connect RS485 interface: Connect RS485
wire from control device to the Data+/Data-
terminal (7).
8. Connect control signal: 4 alarm IN and 2
alarm OUT terminals are available (7).
9. Connect power supply (8): Only 24 V AC
±10 % power can be supplied for this
product, voltage over this range will
damage the product.
10. Connect power source to power terminal.
Start up procedure
When powered up, the Speed dome will
perform a brief homing routine during which it
checks its function and will then go its start
position. The camera information including
model number, software version, protocol,
address setting and communication baud rate
are displayed on the screen.
SIEMENS
(Model)
VERSION***
PROTOCOL***
ADDRESS**
COMM***
Information
For more detailed information please refer to
the Installation & Configuration Manual for
CCDA1445.
Disposal
All electrical and electronic
products should be disposed of
separately from the municipal
waste stream via designated
collection facilities appointed by
the government or the local
authorities.
EN
08.2009
Advertisement
