Advertisement
Quick Links
XC60J Quick Guide【English】
__p
Front Panel
F1. USB 3.0 port
F2. USB 2.0 port
F7
F8
F9
F3. Mic-in
F4. Headphone
F5. Power switch / Power LED
F6. HDD LED
F7. COM6 port (RS232)
F8. COM7 port (RS232)
F9. COM8 port (RS232)
F1
F2
F3
F4
F2
F5
F6
Back Panel
B1. DC power port
B2. LAN port
B3. USB 2.0 port
B4. Kensington
B2
B4
B5
B7
B9
B12
B5. D-Sub (VGA) port
B6. HDMI port
B7. COM2 port (RS232)
B8. COM1 port (RS232/422/485)
B9. COM4 port (RS232)
B10. COM3 port (RS232)
B11. Clear CMOS
B1
B3
B6
B8
B10
B11
B12. COM5 port (RS232)
COM PORT (COM1_2, COM3_4)
RS232/422/485:
COM1_2 (Down)
1 2 3 4 5
1=DCD_485TX-
6=DSR
2=RX_485TX+
7=RTS
3=TX_422RX+
8=CTS
4=DTR_422RX-
9=RI(NA)
5=GND
10=N/C
6 7 8 9
Motherboard Illustration
COM (x2) port
Clear CMOS button
COM power switch-JP7
J13
COM power switch-JP8
J13
LPC header-LPC1
J1
Audio connector-AUDIO1
J2
Battery connector-CN1
J3
COM port header-COM5
J12
DDR3L SODIMM slot-DIMMA1
COM power switch-JP9
J13
COM port header-COM6
J12
COM port header-COM7
J12
COM port header-COM8
J12
COM power switch-JP2
J13
AC back auto power on-JP5
J4
Front USB 3.0 header-USB4
J5
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended
by Shuttle. Dispose of used batteries according to the manufacturer's instructions.
Jumper Settings
LPC header (LPC1)
J1
1=LPC_24M
2=GND
3=LFRAME
4=NULL
5=SIORST-
6=NC
7=LAD3
8=LAD2
9=+3.3V
10=LAD1
11=LAD0
12=GND
13=LPC_48M
14=PCH_PME-
15=+3.3VS
16=SERIRQ
17=GND
18=CLKRUN_NC
19=PD#_NC
20=SUS_CLK_TPM
Audio connector (AUDIO1)
J2
J3
1=MIC_L
2=AGND
3=MIC_R
4=FRONT-JD
5=HP_R_C
6=MIC-JD
7=SENSE B
8=NULL
9=HP_L_C
10=HP-JD
9
7
5
3
1
lock port
®
10
8
6
4
2
AC back auto power on (JP5)
J4
1=PWRSW-
1
2=GND
2
OPEN (Enabled)
Front USB 3.0 header (USB4)
J5
1=USB30_PWR
2=USB30_PWR
4=USB30_PWR
5=U3_RX0N
7=GND
8=GND
10=U3_TX0P
11=GND
13=USB0_N
14=USB0_P
16=USB30_PWR
17=USB30_PWR
Only RS232:
19=U3_RX1N
20=U3_RX1P
COM1_2 (UP) and COM3_4
22=GND
23=U3_TX1N
25=GND
26=GND
1=DCD
6=DSR
28=USB2_P
29=GND
2=RX
7=RTS
3=TX
8=CTS
30
4=DTR
9=RI(NA)
5=GND
10=N/C
SATA power connector
J6
J7
(+5V)(PW2)
1=GND
1
2=GND
2
COM (x2) port
3
3=+5V
4
D-Sub (VGA) & HDMI port
4=+5V
LAN (x1) & USB 2.0 (x2) port
Fan connector (FAN1)
J8
DC power port
1=GND
2=+12V
M.2 2230 A,E key slot
3=SPEED_SENSE
M.2 2242/2260/2280 M key slot
4=PWM_CTRL
Front USB 2.0 header (USB2)
J9
1=USB_PWR
2=USB_PWR
DDR3L SODIMM slot-DIMMB1
3=USB4_N
4=USB3_N
5=USB4_P
6=USB3_P
7=GND
8=GND
SATA connector-SATA1
9=NC
10=GND
SATA power connector
J6
(+5V)-PW2
USB 2.0 connector (USB3)
SATA power connector
J10
J7
(+12V)-PW1
1=GND
CPU
2=USB1_P
3=USB1_N
4=USB_PWR
Fan connector-FAN1
J8
Front USB 2.0 header-USB2
J9
Power header (SW2)
J11
USB 2.0 connector-USB3
J10
1=HDLEDPWR
2=PWR_LED
Power header-SW2
J11
3=SATALED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NULL
10=NA
COM port header (COM5,COM6,COM7,COM8)
J12
1=DCD
2=RX
3=TX
4=DTR
5=GND
6=DSR
7=RTS
8=CTS
9=RI(NA)
10=N/C
COM power switch (JP7,JP8,JP9,JP2) (DEFAULT=SHORT 1-2,3-4) RI(NA)
J13
COM1_2(Down) & COM1_2(Up) POWER SWITCH : JP7
Support RS232 Back panel
Independent External Power 12V / 5V
20
19
JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal.
18
17
JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal.
16
15
IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is VCC
13
14
IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is VCC
12
11
IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V
10
9
IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V
8
7
6
5
COM3_4(Down) & COM3_4(Up) POWER SWITCH : JP8
4
3
Support RS232 Back panel
2
1
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI3 Signal.
Battery connector (CN1)
JUMP2 Connector Pin 3 and Pin 4 = RI4 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI3 is VCC
1=V_BAT
IF JUMP2 Connector Pin 6 and Pin 8 = RI4 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI3 is 12V
2=GND
IF JUMP2 Connector Pin 8 and Pin 10 = RI4 is 12V
A. Begin Installation
1 2
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew the two thumbscrews of the chassis cover.
SHORT (Disabled)
3=USB30_PWR
2. Slide the cover backwards and upwards.
6=U3_RX0P
9=U3_TX0N
12=GND
2
15=USB30_PWR
1
18=USB30_PWR
21=GND
24=U3_TX1P
27=USB2_N
30=GND
1
3. Unfasten the rack mount screws and remove the rack.
SATA power connector
(+12V)(PW1)
1=GND
3
2=NC
2
3=+12V
1
4
3
2 1
HDD rack
10
9
8
7
6
5
4
3
2
1
4
B. Memory Module Installation
3
2
1
This mainboard does only support 1.35V DDR3L SO-DIMM
memory modules.
1. Locate the SO-DIMM slot on the mainboard.
2
4
6
8
10
2. Align the notch of the memory module with the one of the memory slot.
1
3
5
7
9
Notch
9
7
5
3
1
10
8
6
4
2
The product's colour and specifications may vary from the actually shipping product.
L
9
7
5 3 1
COM5 & COM6 POWER SWITCH : JP9
Support RS232 Back panel
JP7
Independent External Power 12V / 5V
10 8 6 4
2
JUMP1 Connector Pin 1 and Pin 2 = RI5 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI6 Signal.
1=-XRI1(NA)
2=COM_-XRI1(NA)
IF JUMP1 Connector Pin 5 and Pin 7 = RI5 is VCC
3=-XRI2(NA)
4=COM_-XRI2(NA)
5=+5V
6=+5V
IF JUMP2 Connector Pin 6 and Pin 8 = RI6 is VCC
7=COM1_PWR
8=COM2_PWR
IF JUMP1 Connector Pin 7 and Pin 9 = RI5 is 12V
9=+12V
10=+12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI6 is 12V
9
7
5 3 1
COM7 & COM8 POWER SWITCH : JP2
JP8
Support RS232 Back panel
Independent External Power 12V / 5V
10 8 6 4
2
JUMP1 Connector Pin 1 and Pin 2 = RI7 Signal.
1=-XRI3(NA)
2=COM_-XRI3(NA)
JUMP2 Connector Pin 3 and Pin 4 = RI8 Signal.
3=-XRI4(NA)
4=COM_-XRI4(NA)
IF JUMP1 Connector Pin 5 and Pin 7 = RI7 is VCC
5=+5V
6=+5V
IF JUMP2 Connector Pin 6 and Pin 8 = RI8 is VCC
7=COM3_PWR
8=COM4_PWR
IF JUMP1 Connector Pin 7 and Pin 9 = RI7 is 12V
9=+12V
10=+12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI8 is 12V
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
1
3
2
45-degree
angle
Latch
Latch
5. Repeat the above steps to install additional memory modules,
if required.
DIMMB1
DIMMA1
C. Component Installation
1. As shown, unfasten the screw first.
M.2 2230 A,E key slot
M.2 2242/2260/2280 M key slot
2. Install the M.2 device into the M.2 slot and secure with the screw.
3. Untie all cables for easier installation.
Purse lock
4. Place the HDD or SSD in the rack and secure with the four screws.
E
For the 2.5" HDD/SSD
SO-DIMM slot
9
7
5 3 1
JP9
10 8 6 4
2
1=-XRI5(NA)
2=COM_-XRI5(NA)
3=-XRI6(NA)
4=COM_-XRI6(NA)
5=+5V
6=+5V
7=COM5_PWR
8=COM6_PWR
9=+12V
10=+12V
9
7
5 3 1
JP2
10 8 6 4
2
1=-XRI7(NA)
2=COM_-XRI7(NA)
3=-XRI8(NA)
4=COM_-XRI8(NA)
5=+5V
6=+5V
7=COM7_PWR
8=COM8_PWR
9=+12V
10=+12V
E
For the 3.5" HDD/SSD
5. Connect the Serial ATA and power cables to the HDD or SSD.
For the 2.5" HDD/SSD
E
Serial ATA cable
Serial ATA power cable
E
For the 3.5" HDD/SSD
6. Slide the rack in the chassis and refasten the four screws.
E
For the 2.5" HDD/SSD
E
For the 3.5" HDD/SSD
D. Complete
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Please press the "Del" key while booting to enter BIOS. Here,
please load the optimised BIOS settings.
53R-XC60J3-H001
Advertisement
